20 Most Recent RCA TruFlat 27F520T 27" TV - Page 4 Questions & Answers

Assuming you are not accidently sitting on the remote, I would say either the power supply or main motherboard has failed. Time for professional service or a new TV.

In most ceases, you might have its original remote control to unlock it. Anyway, try this. 1.Hold down MENU on the remote and VOLUME DOWN on the TV it's self at the same time for at least 4 seconds. The set won't say so, but the lock will be unlocked 2.Hold down the 0 on the remote and the VOLUME DOWN buttons on the TV its self at the same time for at least 4 seconds. The set won't say so, but the lock will be unlocked 3.Hold down the MENU button on the front of the TV and the TV button on the remote at the same time for at least 4 seconds. 4.Hold down GO BACK on the remote and MENU on the front of the TV at the same time for at least 4 seconds. 5.Hold down EJECT on the front of the TV and the MENU button on the remote at the same time for at least 4 seconds. Depending on the model, one of the methods should unlock the V-chip. Now, if desired, you can change the settings on the V-chip by going to the MENU and going to PARENTAL CONTROLS, or on some sets, going to MENU and then going to TV SETUP, then to V-CHIP SET. If you wish to get some details, http://electronicshelponline.blogspot.com/ Pull up older posts.

What you're hearing is the descriptive audio track included on many DVDs for vision-impaired viewers. Does this happen when you're watching regular TV or just with DVDs? If it happens with regular TV, do you have a cable box?

Regular broadcasting sometimes uses SAP (second audio program) to send additional audio, and this descriptive audio may be the SAP channel on some programs. Check your TV's audio settings to make sure you don't have SAP turned on. There may also be settings for SAP in your cable box as well, so check there too.

When playing a DVD, descriptive audio is usually an alternate audio track. Check your DVD player setting to make sure you've selected normal audio for playback.

Hello
From its main Menu, surf towards its sound Menu.
By using UP/DOWN buttons of the remote handset, select SAP

SAP (Second Audio Program) (for analog channels only) Plays the

program's audio in a second language, if one is available. The TV displays

the word SAP in the channel banner when you tune to a program that is

broadcast with SAP information. SAP audio is broadcast in mono. SAP is also

used to broadcast a program's audio with descriptions of the video for the
visually impaired. Press the right arrow button to turn SAP on or off.
OK.

Vertical scan output section circuit fault. Contact any service technician, to replace the damaged component/s. To get some details, http://electronicshelponline.blogspot.com/ Pull up older posts.

029,025,020. Try these codes. For more information check this link. Setup procedure, and setup code list to many popular remote controls are given. Pull up older posts.

It's trying to speak to you... it wants you to repair it. It must be where the relay is that turns the tv on with the remote control. All aging electronics needs the electrolytic capacitors replaced. When they age they throw the voltage off and cause many other parts to blow up. Aging solder joints could be a factor too. look for parts that have been overheating. The circuit board may have parts desoldering themselves and or overheating the circuit traces.

Press the button marked as "CC" on its remote control once.

check weather any swallow uf capacitor

Refer the user manual to this RCA Tv, for more details

some tvs like the one i used to have did th same thing. turned out the remote eye on front of set needed cleaned. worked fine afterwards. also remote buttons are bad about getting stuck you might try cleaning it by taking it apart cleaning it with alcohol. hop this helps

What do you mean

HiI repaired a tv set which has the same symptom. The problem was overvoltage as a filter capacitor in the line supply dried up and the voltage got out of control. I replaced both line supply filter capacitor and the RGB supply filter capacitor (47uF/250V) and the fault was fixed.I hope this hint helps you.Sully

the easy way is in menu-settings -restore to the factory default.