20 Most Recent Amana AEW3530DD Electric Single Oven Questions & Answers

sounds like it blew a fuse or the heating element burnt out on it,look to see if the element is burnt in two

My oven was locked and would not open. No lock light was on but the oven was clearly locked. F9 error when I hit certain buttons.Try this. I unplugged the oven for about 5 minutes. Plugged back in. A LOCK light came on. Held down "Oven Cancel" for a few seconds. Door opened and lock light went off. No more F9 error when I hit those buttons.

F1 code and continuous beeping. This is a common problem with that type of Amana control. The control panel has a design problem I think, and it gets dirty and worn over time. I have replaced mine once, and it happened again less than 2 years later. I took the control panel out, and inspected it. I found a web solution, that said to shim the control panel out away from the housing slightly because it rubs on the metal around the opening and damages the control board contacts. I could see little scratch marks on the plastic skin around the edge of the button area, so that made sense. I tried that, and it still did not work.....panel was still beeping. Mine seemed to be the timer control that was going on and off, and then eventually an F1 error. So, I took the panel out again, and actually peeled the control surface off of the control board. No going back now, I thought. I got it off....it is really sticky.......and looked at the control panel itself . It looked fine, but there was a lot of gunk and wear marks around the edge of the plastic button area. I cleaned it up with alcohol swabs, and checked to make sure none of the printed circuit paths had any wear or damage, and then put the cover back on the board. It was still sticky enough to go back on, and stay in place. I reinstalled it, and "bingo" no more problem. It has been fine for 3 months now. Yahooo! The pic below is just an example pic from the internet. My model is slighty different, but the panel looks basically the same.

Hello & Welcome to FixYa

F3 error code indicates a open/shorted oven temperature sensor and to solve this problem the sensor needs replacement. If you wan to be sure before replacing the sensor then you can test it with a voltmeter for around 1100ohms....if it reads more then this then it needs replacement however, if the reading is around or less then 1100ohms then it is the control board that needs replacement. Please get back to me if you have any other questions.

Kevin

Hello there and thank you for using fixya
Well i wish i had better news for you but your f1 code is teling you that 1 of 2 things are failing.
First is that you electronic range controle has failed and needs to be replaced
Or that your touchpad has stuck and needs to be replaced .
Here is how to test to see which one it is
Determine if problem is with the Key Panel or Control by:
1. Pushing CLEAR/OFF pad.
Remove the back panel from the oven controls to expose the controle panel .
2. Disconnecting Ribbon Cable from control and waiting at least 32 seconds to see if Code recurs

If code recurs, problem is in the control. Replace control.

If code does not recur, problem is with the Key Panel.

replace bottom element

Your lower(bake) element is going bad.
It must be replaced.

it could either be a hot spot in the element where it can no longer pass all the current needed for proper operation in heating(look for a discolored spot on it,it may be whitish and dimpled from heat) or secondly,it could be the oven thermocouple located on the inside top of the oven cavity

This oven has an oven vent that comes out under the control panel usually to the right. Very poor design as this vents heat into the controls and can cause a control board failure, especially during a self cleaning cycle. Good Luck, Appliance Specialists

HI.Your issue will be with the membrane switch pad(touch pad). These two control buttons that you are referring to are damaged(circuit failure). This is not repairable. This will require you to replace the entire touch pad board. Once the touch pad is replaced, the unit will return to its normal operating status.

Touch Pad Part Number 31861403C

My problem was not with an Amana single oven but aMoffatt double oven ! However I have now decided to buy new.

Hi. this is a control fault beep, unfortunately. have the EOC(electronic oven control board), replaced asap, if possible. it has failed.

Replace your bake element. Common problem.

I repair commercial cooking equipment for a living. When a customer complains about uneven cooking the #1 thing that these manufacturers ask is..... are they turning (180*) the baking sheets half way thru the cook cycle. #2 are they staggering the pans front to back & side to side. It's kind of a pain but, works for the commercial ones.

Hi!!! your door hinges are bad they need replacing..very expensive fix..So look around..Good luck..