20 Most Recent
Denon AVR-2807 Receiver - Page 4 Questions & Answers
Powering On Problem
out of the box if this unit is doind this it needs repair, the other things youcan try is check all spkr connections, if good make sure the 2nd zone audio level is down to about -60
How do you reboot the Denon AVR-2807 to factory settings
To reboot, turn receiver off by the small on/off button, not the big standby button. While off press the night and pure direct button at the same time and keep holding them with your right hand while pressing the small on/off button with your left. You will see your receiver menu flash. When you see it flash let go of the night and pure direct button and the receiver will reset it self to the radio station 87.50. The receiver's microprocessor has now been set back to factory. Enjoy this info is straight from Denon's Tech support. I had to do this on mine
Volume settings
Check that level setting for speakers as well as sound field are the same for each input mode. Some receivers will have different max volume levels depending on these settings.
Display on Denon AVR-2307 won't work
It may seem obvious, but have you checked the display dimmer settings? Under the front cover is a button marked dimmer. Pressing it cycles through progressive display dimness settings until it goes off. One more press goes back to full brightness.
AVR 2807 shuts off at high volumes
You may have leaky Caps in the power supply or else dry joints on the amplifier section. Faulty speakers or overdriving of the system may result in the amp going into protection. Good Luck, Jus004
Denon AVR Reciever
You might have a short somewhere behind the back of your receiver.Maybe a speaker wire sticks out and it is touching the back of the metal panel,or an RCA connection to a wrong input or output.
It is common because when you are behind the receiver for so long,carelessness will cause you.
A professional A/V troubleshoot expert could pin point certain connection to fix it for you,but in your case,it will be the best to unplug everything first,turn on the receiver by itself and see if there is anymore shut off;if it doesn't shut off after you have nothing that is connect to but only the power cord,i prove my point!
Let me know,
solutiondoct
Condition on HDMI input when Denon AVR-2807 switched off
hello if you know this spitter conduct voltage and its feed from main device and when you connect another it send it ground you have to do this chech with a voltmeter in the hdmi splitter output is not dc present if so change it cause is not blocking dc current saludos
Denon Receiver keeps changing channels
hello my friend this is happening cause you have a push in button,disconnect from ac take a near look and push the reset button you must check your remote too saludos
Denon AVR 2807 with Bose Acoustimass 15
Well,i can tell you are not very focus,cause you posted Denon AVR-2807 with Bose AC 15 problem,but under your details,you put down AVR-5807!
First of all,it is so unfortunate that you are NOT able to gain and experience to true ability in sound for this wonderful receiver when you are using a dual tweeters speakers and expect to have good sound separation as a TWO WAY speakers(a tweeter and a midrange-for true high frequency and mid frequency sound separation.)
Secondly,you have defeated the audio configuration of the Denon AVR-2807,since all your speakers are control BY the Bose subwoofer.
Now,i could show you a way to hook this up,and it doesn't matter how you connect them, they are the "bicycle tires" installed with a "Porche"engine if you know what i mean.
If you want a good recommendation for your "beast",i will more than happy to show you the way!
Cheers,
solutiondoct
HDMI connection???
Hi Greg,
Again, if you have a high definition dish box with HDMI output,and a
dvd player with HDMI output,please connect them both directly to your
TV HDMI inputs.
When watching TV(dishnetwork box).remember to switch the HDMI video inputs.
Same as your DVD player,you need to switch it under your TV video input.
solutiondoct
Denon 1905/785 - lost color feeding tv
Your Denon 1905 might be setting it under HDMI for video source.You
need to correct it by going to menu,as you browse through the
setting,you should able to find video select or video output. It is on
the manual.
Remember,you need to run a composite video cable from the video output
behind your receiver to your TV video input for this step.
solutiondoct
GE Smartcom
The amount of steps you need to have the GE smartcom systems IR's to work on a Directv R15 box is NOT worth your time and money.
Sorry!
solutiondoct
Sound problem
Maybe you do have a cricket behind your TV? Gee......i don't know how to help you,cause i don't know the rest of your components and how they are connected?
solutiondoct
Operating my ipod docking station
Absolutely!
Keyword(Read the instruction and follow it step-by-step.) Well,if you do,you wouldn't be asking for help,cause you want a 50+ pages Denon manual instruction to be concise to few paragraphs so you could move on with your life-:o)
Okay.only this time!
Denon ipod docking station comes with a power plug and a set of cable which you need to connect behind the Denon AVR-2807 receiver which is under an INPUT LABEL for IPOD only(not going to give it away,you will find it!)
Now,of course you could use HDMI......but,the quickest way to view your video(on screen menu) will be using a composite(RCA) video cable to connect from the Video output(yellow color) from the receiver to the TV composite video input.Turn on your IPOD,and you are ready to see the on screen manual.
Hey,this is just a lazy way to start you off if tomorrow night you have a date;otherwise,set it up properly by using the instruction!
Cheers,
solutiondoct
Lost picture on my AVR-2807
There is a video select button on the receiver. Press it and it toggles through all of the video sources. Keep pressing it until the display says video=source.
Not finding what you are looking for?