Dremel Variable - Speed Multipro Rotary Tool 395 - Answered Questions & Fixed issues


There is a collet stuck in there. It was probably in there without any tool in place, then the collet nut was tightened. With no tool filling the hole in the collet, it collapsed and became small enough to be pushed too far in. Fortunately these collets are soft steel. Find a sheet metal screw that you can screw into the hole. That will allow you to pull the collet out. Discard that collet. These collets come in at least two sized to accommodate different sizes of tool shafts. Unfortunately the spare one you have is one of those sizes, and the one you extracted is probably the other. But they don't cost much and you can buy them where you buy dremel tools. Good luck, Al K

Dremel Variable... | Answered on Mar 12, 2018 | 658 views


Hello, M8052895 -

I found a list of authorized Demel repair centers in the Philippines here:
http://www.dremel.com.ph/ph/en/service/after-sales-service/dremel-authorised-service-centre-list/

If you scroll down that page, you will find a Philippines contact telephone number.

Best wishes.

Dremel Variable... | Answered on Mar 05, 2018 | 171 views


http://www.searspartsdirect.com/part-number/2610914543/0009/170.html

Dremel Variable... | Answered on Apr 18, 2015 | 617 views


How stable is your line voltage? The SCR phase control used for speed control is more sensitive to line voltage changes at low speeds than at high speeds. Brushes should be changed when they are worn down to about 1/2 of their original length. Much more than this and they don't have enough tension to properly contact the commutator ring. Check with power off when the tool is cold and slowly turn the chuck by hand to feel the resistance. Run it a while and let the bearings warm up. Turn off power and turn by hand again. If it feels looser when warm (which would cause it to speed up at slow speeds), the tool might need to be disassembled and bearings oiled. I use Dexron automatic transmission fluid to lube most motors. Wipe down any excess.

Dremel Variable... | Answered on Nov 29, 2014 | 184 views


I usually just tap it gently with a piece of wood directly on the end of the bit. This will usually loosen it up. This also works with a router.

Dremel Variable... | Answered on Oct 27, 2014 | 54 views


with tool unplugged rotate tool end with your finger tips if it gives any resistance to this your bearings have forign material in them (happens if your doing grinding allot) if a liberal dose of light oil (sewing machine) does not improve this friction im sorry but you;ll have to replace tool to run slower speeds

Dremel Variable... | Answered on Sep 05, 2014 | 82 views


the collet is either the wrong size for the shaft on the attachment or is missing alltogether

Dremel Variable... | Answered on Oct 25, 2018 | 822 views


You will have to remove the plastic cap on the end of the tool where the tips go in. Then screw on the cutting guide.

Dremel Variable... | Answered on Aug 27, 2014 | 87 views


Perhaps you are bending the shaft too much, or the original lube in the flex shaft has been compromised. Take it back to the dealer, for an exchange.

Dremel Variable... | Answered on Jul 13, 2014 | 146 views


Lowes, home depot and Sears sell them. Also, dremel.com sells parts.

Dremel Variable... | Answered on Jul 22, 2014 | 59 views


Burnt out brushes.

Dremel Variable... | Answered on May 08, 2014 | 480 views


dremel have a collet adaptor available to allow interchange of bits. They are available from dremel or hardware stores.

Dremel Variable... | Answered on Aug 09, 2013 | 188 views


I don't know about purchasing one, but you may download a free copy of the manual from http://www.dremeleurope.com/za/en/ocs/product/7359/2/multipro/dremel%C2%AE-multipro%C2%AE

Dremel Variable... | Answered on Dec 15, 2013 | 253 views


Press release button and hold down while unscrewing bolt. Continue to hold button and unscrew bolt until tip is loose enough to pull out if it still won't come out unscrew all the way, take bolt off and pull out tip with channel locks. It just got jammed in when tightening because diameter is probably a little wider

Dremel Variable... | Answered on Mar 16, 2013 | 59 views


I have a Dremel 395 Type 3. Motor works fine, shaft doesn't turn. Took it apart to find that the white plastic or nylon flex coupling on the shaft had crumbled and the spline driver, which fits directly over the motor end of the shaft was somewhat worn. I emailed Dremel and got an overnight reply listing the 2 parts I need and the cost: Coupling is $1.00 and the driver is $1.25. Placed order by phone: 1-800-437-3635. I ordered 2 of each in case future replacement is needed. Total bill came to $7.27 including Florida tax and shipping. Can't beat that. They said it would be in the mail by tonight. (Flex coupling number is 2615294309; spline driver is 2615294308.)

Dremel Variable... | Answered on Jul 25, 2014 | 20,062 views


Hi Larry, The tool that you require parts for was discontinued many years ago. Limited parts are available from Dremel. Inside the tool is a flex coupling and spline driver. The flex coupling is # 2615294309 and the price is about $ 1.25. This is the hollow plastic sleeve about 1" long with grooves on the inside, that goes between the motor shaft and the output shaft. The spline driver is # 2615294308 for about $ 1.00. Spline driver sits on the direct end of the motor shaft. The flex coupling sits over the spline driver. Spline driver is about 1/4", hard plastic with grooves on the outside. Total shipping for orders under $ 5.00 is $ 2.50. Orders over $5.00 is $ 4.00. There could be a tax charge depending on which state you live in. Here is how to order: Call Dremel Customer Service at 1-800-437-3635 , Monday-Friday from 7 am to 6 pm central time. VISA, MasterCard or Discover to place a Visa, MasterCard or Discover order. To order by mail: Dremel 4915 21st Street Racine, WI 53406 USA 1-800-437-3635 ext. 3636

Dremel Variable... | Answered on Feb 14, 2013 | 553 views


find the little square attachment and place on the end of the dremel tool. I didid the same thing. Worked fine after I put the other part on.

Dremel Variable... | Answered on Oct 25, 2018 | 515 views

Not finding what you are looking for?
Dremel Variable - Speed Multipro Rotary Tool 395 Logo

197 questions posted

Ask a Question

Usually answered in minutes!

Top Dremel Tools & Hardware - Others Experts

cluffermon

Level 1 Expert

4 Answers

Mike

Level 3 Expert

4363 Answers

Van Allen II
Van Allen II

Level 2 Expert

273 Answers

Are you a Dremel Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...