20 Most Recent Dremel Variable - Speed Multipro Rotary Tool 395 - Page 9 Questions & Answers


hello,

try to find it here:

http://www.powertoolspares.com/parts2.php?model_ID=3057

may this help.

melnavz

Dremel Variable... | Answered on Jul 23, 2008


threw it in the trash!

Dremel Variable... | Answered on Jun 25, 2008


When the brushes go on my Dremel, it just stops, sometimes erratically - no smell or burning.

Dremel Variable... | Answered on May 23, 2008


spray lube or oil and use pliers to move it back and forth

Dremel Tools &... | Answered on Jun 03, 2019


Fixya is unable to suggest sources for Dremel parts.

Dremel Tools &... | Answered on May 14, 2019


It's possible that the enameled copper coiling on the stator was compromised when it overheated creating a short. Sadly, unless you have a replacement stator is cannot be fixed. Sorry.

Dremel Tools &... | Answered on Feb 11, 2019


3 in 1 is a light oil used the lubricate small joints, plates and bearings. It can also be used as a releasing oil for stuck bolt etc. 3 in 1 is usually ok to use in small amounts to grease the bearing points on your Dremel.

Dremel Tools &... | Answered on Dec 23, 2018


You can use canned air for light dirt,or compressor with blow gun for heavier dirt.

Dremel Tools &... | Answered on Nov 04, 2018


I don't know if it has a fuse - I know little about the Dremel brand but I have had some experience of similar other brand tools. The electronics seem less than completely reliable being physically too small for the job of speed regulation, torque compensation, radio interference suppression, etc. - everything is crammed into a tiny space and the circuit board is typically on the cheap and nasty side. If there is a fuse it would typically be found on the circuit board.

Mostly the failure of such tools, in my experience, is caused by the electronics though nothing can be ruled out.

I suggest you check the mains cord using a multimeter and then check the motor and if both are OK it is fairly safe to assume the fault is circuit board related.

Dremel Tools &... | Answered on Oct 27, 2018


No.. the issue issue is the switch inside. when your Dremel 4200 stop working, press firmly the grey area between the speed selector and the brush housing. I think this a defect in the design of the 4200. 9f840401-fb84-4f7b-8c68-75a9be3ceb9e.jpg

dremel-4200-stopped-working-sc23h3bxyncdov434g0b1kv3-5-2_0.jpg

Dremel Tools &... | Answered on Oct 08, 2018


The flashing light indicates an error, possibly your battery is shot or malfunctioning. New battery needed.

Dremel Tools &... | Answered on Oct 02, 2018


search for one using Google

Dremel Tools &... | Answered on Jul 23, 2018


The Dremel 200 has two speed control which allows you to set your speed at 15,000 or 35,000 rpm with a flip of a switch

Dremel Tools &... | Answered on Jun 12, 2018

Not finding what you are looking for?
Dremel Variable - Speed Multipro Rotary Tool 395 Logo

197 questions posted

Ask a Question

Usually answered in minutes!

Top Dremel Tools & Hardware - Others Experts

cluffermon

Level 1 Expert

3 Answers

Mike

Level 3 Expert

4357 Answers

Van Allen II
Van Allen II

Level 2 Expert

272 Answers

Are you a Dremel Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Dremel Tools & Hardware - Others

  • Dremel Tools & Hardware - Others

Most Popular Question

flexible extension not working dremel

  • Tools & Hardware - Others
Loading...