20 Most Recent Dremel Variable - Speed Multipro Rotary Tool 395 - Page 4 Questions & Answers


You will most likely need to purchase a used parts unit - look on Ebay they're very cheap.

Gary @ Fix Ya

Dremel Variable... | Answered on Jun 16, 2011


Electrically speaking there are a few items to check.

1) The easiest is to remove the two brush holders screws on each side by the power cord. If one of the screws are loose, or the bushes are worn you will get intermittent or no operation.

2) Second use a volt ohm meter to make sure you have voltage on the two brush connectors inside the brush holders when power is on. If you do then open the unit a check continuity on the motor armature to see if it is open, which will cost $13.37. If you do not have voltage, inspect the power cord and switch.

Some parts can be purchased on the below link.

http://www.ereplacementparts.com/dremel-395-f0130395ca-corded-multitool-parts-c-15440_15456_15474.html


Or contact a dremel service center from the link below.

http://www.dremel.com/en-us/customerservice/ServiceAndRepair/Pages/default.aspx

Dremel Variable... | Answered on Apr 27, 2011


I found a coupling part at ereplacementparts.com and the part number is 2615294309, but I would recommend calling Dremel direct at 1-800-437-3635 to ensure this is the right one. They made a change on this coupling. Let me know if you need more assistance.

Dremel Variable... | Answered on Apr 18, 2011


The coupler nut tends to be screwwed on so tight that even when undone, the collet has bit into the soft shaft of the tool. Holding the rotation lock button in, grab the shank with some strong needle nose pliers and twist the shaft loose or pull it off completely with the nut and then seperate the nut from the shank when it is out of the Dremel Tool. A lot of machine tools are tightened too much, which makes the shanks get all damaged so use only the required tension on that collet nut.

Dremel Variable... | Answered on Mar 29, 2011


Hello marty. Lay out the knotch in the post with a square and a pencil. Cut the lines to the proper depth with a saw and then use either the dremel tool or even a chisel and a hammer to remove the waste. Joe

Thanks for choosing Fixya!

Dremel Variable... | Answered on Mar 24, 2011


YOU HAVE TO LINE UP THE POST WITH THE BUTTON AND THEN PUSH AND RELEASE ROD THERE SHOULD BE A MARK ON IT. GOOD LUCK

Dremel Variable... | Answered on Mar 09, 2011


OK there's not much to these first check, the power plug, check cable, if you can, open it up and see if there is power to the On/Off switch, if there is check the switch, if they are all good but still no go, then most likely culprit is the speed controller, you will need to replace it.

Dremel Variable... | Answered on Mar 02, 2011


There is a red switch at the back with controls the speed. Assuming you've tried that, the tip may not be tightened on tightly enough and is spinning inside the shaft.

Dremel Variable... | Answered on Mar 02, 2011


Try at eReplacementParts.com : Power Tool Parts and Tool Repair Diagrams.

If you need more help post back!
Thumbs and testimonial are welcome!

Dremel Variable... | Answered on Feb 25, 2011


there in the kit is a shaft with a screw tip on it, you need to thread the polishing disc on the shaft, the shaft has a threaded screw, not the internal type

Dremel Variable... | Answered on Feb 08, 2011


Hi Joe, Joe here. I have a dremel tool now for almost 25 years. Same one. I had this happen to me. You should be able to get the parts at any hardware store that has the big dremel accessories cabinet. You can also get the parts from dremel's customer service. Great tool, next to my leatherman wave. http://www.dremel.com/en-us/Tools/Pages/RetiredProducts.aspx

Dremel Variable... | Answered on Jan 31, 2011


Welcome to fixya

Hello


I have a solution for this


Press Ok, Accept or replay so we may get started


Your pre-solution is coming up shortly


PLEASE REPLY OR LEAVE COMMENT TO CONFIRM YOU RECEIVED THIS EMAIL


My name is Bruce

Dremel Variable... | Answered on Jan 17, 2011


contact them direct at dremel.com and you can download a schematic which I think the locking collar/mechanism is rounded but they also have a toll free number for technical support.

Dremel Variable... | Answered on Jan 09, 2011


Clamp the bit in a vise or with vise-grips (you will probably ruin it) to hold it while you loosen the collet. You can disassemble the tool and get the lock assembly P/N 2615297356 from for less than $2.00. Search for the part number on line for a source.

Dremel Variable... | Answered on Jan 06, 2011


Check w/ Home Depot and/or Lowes. If they don't stock they can get quickly

Dremel Variable... | Answered on Jan 04, 2011


You have to split the case and remove the entire switch/brush holder from the tool. You can use anything from picks to files to drill bits to get all of the stuck brush material out of the switch. Small files help clean up the holder area. Just be very careful not to damage or break the switch, they have been discontinued and are getting exceedingly hard to find on after-market parts sites. Depending on which version 395 you have, switches are available for a couple of them at www.ereplacementparts.com. The different versions have a number like F0130395XX, where the XX is different for each model variation.

Dremel Variable... | Answered on Jan 03, 2011


You can go to Dremel.com and find assistance or call their toll free number at 1-800-437-3635 and speak with their tech assistance. Let me know if you still need more help. Also I tried using the model number provided and it came up empty that is why I am directing you to this site yourself.

Dremel Variable... | Answered on Dec 29, 2010


Try at eReplacementParts.com : Power Tool Parts and Tool Repair Diagrams.



If you need more help come back.

Post / thumbs / testimonial are welcome!

Dremel Variable... | Answered on Dec 18, 2010


Try at eReplacementParts.com : Power Tool Parts and Tool Repair Diagrams.

If you need more help come back.Post / thumbs / testimonial are welcome!

Dremel Variable... | Answered on Dec 14, 2010

Not finding what you are looking for?
Dremel Variable - Speed Multipro Rotary Tool 395 Logo

197 questions posted

Ask a Question

Usually answered in minutes!

Top Dremel Tools & Hardware - Others Experts

cluffermon

Level 1 Expert

3 Answers

Mike

Level 3 Expert

4357 Answers

Van Allen II
Van Allen II

Level 2 Expert

272 Answers

Are you a Dremel Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Dremel Tools & Hardware - Others

  • Dremel Tools & Hardware - Others

Most Popular Question

flexible extension not working dremel

  • Tools & Hardware - Others
Loading...