Chamberlain Powerdrive PD422D 1/2 HP Security Plus Screw Drive Garage Door Opener - Answered Questions & Fixed issues
My wife paired her Acura
unpair it as there is another signal in your area on the same frequency. some frequencies can travel over a hundred meters or more. if you use a frequency monitor you will find there will be a lot of signals in your area. the original system will drown these out looking for its signal but pairing a device that has a different frequency or frequencies this can cause randone read. and will work on frequencies in this range can even be a freezer turning on etc. as every device make a signal.
2/28/2018 5:45:11 PM •
Chamberlain...
•
Answered
on Feb 28, 2018
•
486 views
I have a SecuraLift Garage
Many of these devices use a code that changes each time the door is opened and closed. This feature is used to keep potential bad people from learning your operational code and entering your garage. You may have a communication problem whereby the Garage Opener needs to be reset. You may try to change the settings. If you have dip switches on the main unit in the garage, change the dip switches to another setting and write down the numbers in the order that you have the set them, Then go to the remotes, hand held and hardware placed on the outside door, and change the settings on these devices to MATCH up with the inside unit. This is a good time to REPLACE the batteries also.
2/20/2018 6:19:01 PM •
Chamberlain...
•
Answered
on Feb 20, 2018
•
1,466 views
I have problem, with my door garage. it desn't
IF THE DOOR OPENS WITH YOUR REMOTE BUT DOESN'T CLOSE (AND WORKS NORMALLY FROM THE WALL BUTTON) THE PROBLEM IS IN THE SAFETY EYES - CHECK TO SEE THAT BOTH LED'S ARE LIT.
IF NOT CHECK WIRING POLARITY - CHECK FOR BROKEN WIRES - CHECK FOR ALIGNMENT AGAIN.
10/24/2017 1:20:44 PM •
Chamberlain...
•
Answered
on Oct 24, 2017
•
438 views
My garage door starts going
take some toilet paper, or some very light rag and dust the RPM sensor over, under, inbetween and in every spot on that darn thing, and bingo, it will work. Its the plastic ribed piece mounted on the end of the motor under opener cover. If something gets under door as door starts to go down, the RPM`s will slow and thats a warning to stop and go back up. With it being dusty, it can`t sense the RPM`s properly and goes into an alarm every single time. Ugg
12/7/2013 8:56:07 PM •
Chamberlain...
•
Answered
on Dec 07, 2013
•
4,003 views
Need to replace carriage on stanley sd450 opener how is it done?
Please make sure you don't have broken springs first and that the door is balanced properly. If so you can replace the "Trolly" by disconnecting the arm from the opener, undoing the opener from the bracket that mounts it to the wall. This usually takes a 1/2 in wrench. Then swing the opener out far enough to slide the trolly off and replace it with a new one. Re-connect everything then re-engage the trolly.
10/1/2021 9:42:41 PM •
Chamberlain...
•
Answered
on Oct 01, 2021
•
1,811 views
Red LED light remains on and beep sound
My battery is bad. I knew it, but did not feel like it was worth any of my attention. The beeping started yesterday and this was worth my attention. Everyone in the family complained. I suspected it was the battery.
I unplugged the unit. Disconnected the battery. Waited for 30 seconds. Plugged it back in. It works fine and no beeping.
I suspect it is a warning to replace the battery.
11/9/2011 2:30:48 AM •
Chamberlain...
•
Answered
on Nov 09, 2011
•
6,878 views
Broken electric eye on garage door opener. How to
The eyes do not stop the door from opening - They only work on the close cycle.
If the door will not open at all it may have a broken spring. Try unhooking the door from the opener.
If it works manually try the opener with the door unhooked.
NOTE: holding down the wall button overrides the safety eyes. This is the only bypass available (you need to get a new eye to replace the broken one.
Hope this helps
4/28/2011 10:45:56 PM •
Chamberlain...
•
Answered
on Apr 28, 2011
•
1,302 views
Not finding what you are looking for?