MagLite - Mag Charger System 110v (M) Model - RX1019 - Answered Questions & Fixed issues

when you dropped it you probably knocked the contacts inside out of place. or you broke a soldered connection. if you can take it apart you can most likely fix this yourself. when you remove the front lens assembly there is a retaining clip that you need to remove so you can take the guts out.....please rate this

Volt meter. Touch one lead to each contact. If you dont have one Harbour Freight has on for around 5.00.

Should be able to get it with tweezers or needle nose.

Hi
I had one about 15 years ago and it was installed in the car.
The click in base used to charge it has a metal base which can be screwed into place in the vehicle.
The base take's 12 volts from your mains charger, If you still have the full kit supplied with the torch you will have got a lead for connecting the base up to the 12 volt supply.
If you do not have the lead you will have to find a lead with the same connection on the end as the mains one.
You will need to use an in-line car fuse holder with a fuse of 6 amp's size to protect the lead and charger. Observe the polarity of the lead coming from the mains charger and duplicate it with the lead in the car. (reversed polarity will prevent the charger from working.)
In my case I used the cigarette charger supply in the car to power it. (the load is very small)
Regards

You might try this website, they should be able to answer any questions.

http://www.maglite.com/feedback.asp

It would be a bad idea. The battery would soon not be able to hold a charge. It's best to charge it up fully and then take it off the charger.

check the output voltage on the power transformer that plugs into the wall. It should be about 7.5v and if that is what it says the it will be defective if the output is actually 12.dc. But if that is what isays it should be then you need to make sure that it is the right power supply.

Unscrew the head (the same way, as regulating throw, but much more rotations), then unscrew the nut, holding the bulb. Assemble the same way - nut then head

Unscrew the head (the same way, as regulating throw, but much more rotations), then unscrew the nut, holding the bulb. Assemble the same way - nut then head

http://www.google.ru/search?ie=UTF-8&hl=ru&q=how%20to%20disassemble%20magcharger&redir_esc=y&ei=Pj5hS7nAHYHFsgachrnPCw

Unless you are using your Mag. in extreme dusty, dirty conditions, it is not necessary to take it apart for cleaning. The Mag. is sealed against dirt and moisture. Mags are about the best lite made but always remember; 'Anything man made is subject to fail and usually at the most inconvenient time.' If I knew exactly where you are at in the dissasembly I could help you reassemble it. However, barring that;
Go to; www.maglite.com, they can help you with what ever you need.
Good luck. :)

I found out the light bulb was bad even though it looked good. Had a fine break in the filament that I couldn't see with my eyes. Pulled the light bulb part way out, put a voltage meter on the two prongs. It showed I had voltage right up to the light bulb which told me the light bulb was bad. Ordered a new one and it works.

8years old.very weak beam no fault to flash halogen lamp . system seems to be not fully charged

Somewhere in the flashlight their is a short, check everything from bottom to top.


GGBMDB

If the charge lite comes on when charging it means your transformer is still good. Replace the battery.

If you get no charge light transformer is bad, if this is the case (personally) i would replace the charger & battery for that peace of mind.



GGBMDB

Charge it for at least 12 hrs before using and run it down every so often to get a complete charge out of it and longer battery life.


GGBMDB

Serial # number is usually stamped on the body of the flashlight towards the top.



GGBMDB

did you replace the switch cover? is it original? does the cover look deformed under neath?
call up the customer service 1-800-283-5562 or email [email protected] if the switch or cover is defective you should be sent a new one at no charge

I have a regular AA Mag light that had industrial strength batteries which corroded.I did get them out but the bulb holder on the light broke.(The main bulb holder where the twist on switch is.)

Mag light offers a lifetime warranty on most products here is thier contact info.

Warranty / Service Address: MAG Instrument, Inc.
1721 East Locust Street - 51453
Ontario, California 91761-7769 Warranty Business Hours: Monday - Friday 7:00 a.m. - 4:30 p.m. Pacific Time Warranty: Phone
Fax 909 947-1006
909 947-5041

Hope this helps You
please rate me.