Canon PIXMA iP4300 InkJet Photo Printer - Answered Questions & Fixed issues
Lines on a photo when printed
The print quality usually depends on the program you're using to print them on your pc.
Your camera only ever sends photos to your printer, so the best settings are already selected by the camera and it's built-in photo program.
Your printer doesn't 'know' whether your printing a document or a photo, so the settings for each program on your computer are basic (known as default settings), and need to be changed by you to get the best from your printer
Find the settings that let you alter the printers options (in Word, it's FILE \ PRINT \ PROPERTIES), and make sure the printer output is set to maximum quality, and that photo paper is selected as the paper type.
Some options such as 'maximum quality' only appear when you've chosen 'photo paper', and some printers (such as the ip4300) have seperate options for gloss or matte paper, so go through all of them until you see what you need.
Hope that helps :)
5/30/2022 1:46:16 AM •
Canon PIXMA ...
•
Answered
on May 30, 2022
•
193 views
IP4300canon printer
The problem is that the ridiculously cheap little plastic piece on the door hinge that is supposed to trip the switch that tells the printer that the door is open is either a) broken off or b) no longer aligned so that it pushes the switch all the way. I solved the problem by removing the top cover and gluing the switch open with super glue.
To open the cover, find yourself a small, flat piece of metal (or stiff plastic) about 1/2" wide and a few millimeters thick. (A very flat-bladed screwdriver will do, but I made myself one out of the non-sharp side of a straight-edge razor blade.) Push this into the 5 slots marked with an arrow around the sides and back of the printer (they're toward the bottom of the sides.) Pry up on the cover at the back and then pull straight up on the front. There are two flat vertical pieces that slide into slots at the front that have to come up - they were tough to make come loose, just try not to break them off.
Pick up the electronic control panel that is on the front right of the printer. (You might have to remove the silver piece of plastic at the right front corner. It pulls straight up to remove.) The switch is the little black plastic piece on the left side of the electronic control panel. Push it to the "open" position (opposite the resting position) and glue it in place. Reassemble your printer and voila! no more annoying "door closed" message!
2/14/2022 6:34:25 PM •
Canon PIXMA ...
•
Answered
on Feb 14, 2022
•
3,515 views
Canon pixma ip4300 - magenta ink is recognized but not printing
Take the print head out of the machine and sit it in a saucer of very hot ( just off boil) water about 10mm deep for a minute. Take it out and sit in on a pad of paper towel to dry briefly before returning it and the cartridges into the machine. Give it a deep clean and try again. If still no good, the print head has probably had it.
11/2/2017 11:52:06 PM •
Canon PIXMA ...
•
Answered
on Nov 02, 2017
•
371 views
Flashing green orange lights
There is many reasons for that,
are you printing any thing???
Just restart the printed and see if lights turned off....
4/5/2015 11:02:36 AM •
Canon PIXMA ...
•
Answered
on Apr 05, 2015
•
542 views
Ip4300 5 blink
One, or more, of your ink tanks are empty. Open the Canon IJ Status Monitor on your computer to check the ink level information. Replace the appropriate tank.
11/7/2014 11:39:01 AM •
Canon PIXMA ...
•
Answered
on Nov 07, 2014
•
87 views
Try to print directly to DVD with a canon pixma
>> It tells me to close the door so it can resume printing on paper normally A4.
It is trying to "ignore" the "bypass" try.
Tell the printer to *ACCEPT* the disk from the "bypass" tray,
rather than from the stack of paper in the A4 tray.
To tell the printer, click the OK button on the printer.
10/22/2014 11:58:16 AM •
Canon PIXMA ...
•
Answered
on Oct 22, 2014
•
239 views
Cannot duplex print pdf files. No problem for over
Printing PDF files without special software can be a problem, if you print a lot of files of different formats and need to deal with a few printers.
Total PDF Printer from Coolutils is a program features a lot of printing modes and adjustable parameters that will help to optimize the process of printing PDF files. To save the paper, it offers ability to print PDF files in duplex mode, i.e. print PDF pages from both sides of paper sheet.
You do not need to turn each sheet by your hands, as the program changes printer settings so that this process is automated.
Total PDF Printer is a perfect suit for personal or professional use for printing PDF files. It automatically connects to all printers enabled in the system and redirects printing tasks to the trays you specify.
Print PDF Files In Duplex Vertical
10/14/2014 7:19:09 AM •
Canon PIXMA ...
•
Answered
on Oct 14, 2014
•
413 views
Why wont the head alignment work?
If the inks will not come out the alignment fails. Have you tried a deep clean? If that does not solve your problem
You can try and soak the head in one oz. ammonia and 8 oz. of hot water. Preferably distilled or spring water. Make sure it covers the nozzles and ink intake ports. Let it soak for 30-45 minutes.
Completely dry the head and contacts being careful of the nozzles
.Maybe let it sit for an extra few minutes
Do a deep clean after installed and if it now does a nozzle check be sure to put paper in the top tray and do an alignment.
If this does not work you may need a print head which I can supply.
Thankls for using Fix-Ya
8/28/2014 3:45:28 AM •
Canon PIXMA ...
•
Answered
on Aug 28, 2014
•
117 views
Not finding what you are looking for?