Top 20 Canon PIXMA MP160 All-In-One InkJet Printer Questions & Answers

Try doing a Reset. Reset Printer Canon PIXMA MX310 or Canon MP160

1. Leave the cartridges in the device.
2. Turn off the printer using the on/off button.
3. Keep the reset button pressed and press the on/off button now also. ...
4. Release now the on/off button. ...
5. Now open the printer and press the On / Off button. ...
6. Now the printer with the on/off switch off button and turn on again.

More items... • Feb. 28, 2017

Reset Printer Canon PIXMA MX310 or Canon MP160 - Printer ...

..

Im pretty sure you should add the printer before downloading the driver. Try uninstalling driver, install printer, the install driver. If it came with software it's better to use it.

Uninstall with MS control panel, then reinstall. Make sure that it will work with Vista first.

We are here to post solutions.

Have you tried to disconnect the printer and then reconnect it?

Hi Pam please don't take this the wrong way but I think it's time you updated your operating system to one that receives support and updates. The problem you have is compatibility between programmes and I don't think there is a cure. Windows 7 or windows 10 should be what your looking for.. good luck !

http://gdlp01.c-wss.com/gds/6/0900002716/01/mp160_ug_us_v5.pdf

http://gdlp01.c-wss.com/gds/6/0900002716/01/mp160_ug_us_v5.pdf .go to this link. its the manual.half way down the pages it shows you how to do it.

t is safe to say that you're looking for Canon PIXMA MP140 Driver ? Just look at this page, you can download the drivers through the table through the tabs below for Windows 7,8,10 Vista and XP, Mac Os, Linux that you want. https://www.canonprintersdrivers.com/canon-pixma-mp140

Reinstall printer driver and reset printer counter

install the cd or find the drivers online follow installation procedures and put usb cable.......... there you are!

hi . try to use the printer status monitor in your pc. it show you exactly what is wrong with your printer.

You can download all you need after selecting your operating system at: http://www.canon-europe.com/support/consumer_products/products/fax__multifunctionals/inkjet/pixma_mp_series/pixma_mp160.aspx?type=drivers&language=EN&os=WINDOWS%207%20(32-bit)

hi. there is a front door or upper door . when it's open cartridge automatically move to the center so you can change them

1. Turn off your color printer 2. Press and have the STOP/RESET button 3. Press and also hold Power ON key 4. While keeping the Power ON switch, discharge the STOP/RESET key 5. While holding still the Electrical power ON button, push two times the STOP/RESET switch 6. Launch the Power ON key 7. Wait until that show an "abandoned" information. It will definitely take about a moment. 8. When "still" appear, open the best cover to leave open the ink cartridges 9. Raise the cover for cartridge holder and also obtain both the and shade containers. 10. Gain the cover from container holder and switch off the printer 11. Gain the leading cover and also switch on the color printer again 12. After the laser printer activate, return the ink cartridges. 1. Push and also Have the STOP/RESET switch and stand by until this personal reboot. 2. Release the STOP/RESET switch the printer is actually restarting. 3. Wait for a few secs Download Driver here https://www.canonprintersdrivers.com/canon-pixma-mg6100-series

Only the manufacturer can program the eprom.

Disconnect the power cord from the back of the Canon Inkjet Printer. This is an important step when working inside ANY electronic device. Unhinge the back access panel of the printer. It seems repetitive to say this, but this door will be in the BACK of the printer. Look through the opened back panel and look for paper. Remove any and all paper you find jammed there. Close the back access panel. Make sure that it latches into place and looks the same way that it did before you opened it. Find the front or top access panel. This is the panel you would lift to change ink cartridges. Open this access panel. If the carriage that holds the ink cartridges moves, then you forgot to unplug the printer, go back and do that now. Look for paper that may be jammed in this area of the printer. Remove any paper you find jammed here. When pulling from the front there will be resistance from the paper feeder. Pull slowly or the paper will rip and create a more stressful problem. Close the front access panel. Make sure that it falls or latches back in place. It should look the same way that it did before you opened it. Plug the printer's power cord into the wall outlet, and attempt to print again. If the printer prints the job, then you have successfully removed the paper jam. or Paper jam error. How to correct, fix: Remove the jammed paper. If paper jams frequently occur, check the following: 1. Confirm there is no foreign material inside the machine. 2. Confirm only recommended paper is installed. 3. Confirm paper is installed properly. 4. Confirm the maximum number of sheets in the auto sheet feeder is within the paper limit mark. or How To Reset Canon Printer MP160, MP180, MP460 How to correct, fix: Reseat ink cartridge for Printer (MP160 / MP180 / MP460) Issue: ERROR LED: E, 1, 4 How to correct, fix: Press ON/OFF switch to reset the multifunction device Reset the device when it is not functioning properly. If the device is not functioning properly or to clear memory, reset it. On the operator panel, press and hold the <ON/OFF> button for one second. (The display will go blank.) Note: It may be necessary to unplug the power cord if pressing the ON/OFF button does not shut off the printer. Wait approximately ten seconds and then press the <ON/OFF> button again. Wait until the device has completed its cycling process before submitting another job request. Turn the machine off, and remove the power cord from the electrical outlet. Wait approximately ten minutes then plug in the power cord and turn the machine on. If the problem is not resolved, the machine may require service. It just may be that the so-called roller cleaning operation may calibrate the timing

Possible error 1. Faulty ink cartridges. 2. Dirt on TIMING SLIT STRIP FILM

Click start, devise and printers, right click on the MP 160 image , click trouble shooter, follow instructions..

Rosemary. Do a deep clean cycle then a nozzle check either from the computer or the maintenance wheel on the 610. May sure all the line are printed correctly. If not remove the head and cartridges and take some hot(not boiling) water and mix it with2 oz. of Ammonia and let the head sit for an hour in a cereal bowl .Re-install after making sure the head is completely dry and check nozzles again. If not working you either have bad cartridges or a bad head. I have a new heads if needed.