20 Most Recent
Sanyo DP42746 42 in. Plasma Television - Page 8 Questions & Answers
I just got it home and I had to lay the tv flat in
Good Morning
I have laid them flat, turned them back up, plugged them in without issue. I think this is just a myth but like all myths there must be some truth.
To be safe wait an hour... Then if its messed up RETURN IT... :)
Have a great weekend
Tv cclicked off and on 6 times quickly and turned
Hi,
This
is an internal fault as you must have observed. There could be many
causes for the same. It could be a problem with power supply board.
Other than this, it could be Y and Z sustain boards. However, it needs a
proper inspection and testing of these components. If you have
electronics repair experience, know how to use multimeter and soldering
iron, could read schematics - i would be glad to provide you with a link
to purchase service manual ( if available ) and could guide you to fix
the problem.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
Turns on suond but no video
could be the ysus board or faulty panel if u are technical minded then open it up after it has been off for at least an hour and unplug the upper and lower board on the left and turn it on and if the screen lights up then u know it is the ysus please let me know and be very carefull if it looks too hard take it to a dealer
I have a Sanyo model#
Tries tv unplug,replug the tv back like an hour later,now the tv is resetting itself back to the factory setting.Now,the tv should be working now.Not,than this problems,the cause is the power supply board have problems.That the board,where the power a/c cord plug into it.Try website like Ebay.com to buy a whole refurbuish power supply board for the replacement.
My mod #dp42647 blows the main fuse 120/5 amp tv
Hi,
As you said main fuse blows that is located on power supply board that indicates that power supply board is defective and need to be replaced to fix the issue.
Hope this info will help you.
Let me know if you have additional question.
Thanks.
The top half of the
Hi,
I am sorry to Hear regarding the Problem.
This is an internal Failure. One of the Boards have actually Failed. If you call a Repairman, it would cost you $300 - $500.
If you wish to Repair it, Revert and i would be able to guide you.Make sure you need to have some electronic skills like Soldering, Use of Multimeter etc. I would be able to tell you where you need to Purchase Service Manual that would have all the Schematics.
Let me know,so that we could Proceed.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
Green light comes on no
Hello Afox5, hi, make sure that there are no user controls or setup that are out of order. as a backgrounder, TV of this type mostly has two boards, power supply and main board. On the power supply board, this has two section, primary that deals with mains voltage and secondary that deals with TV supply current requirements, if you see green light mean that power on the secondary section of the power supply board of your TV is working, but it does not mean that the power supplied to the main board is correct, the supplied current produced by the power supply section to the main board that controls sound and picture needs to be checked, so voltages are needed to be checked and loose wiring, or screws needs tightening, are a common trouble, but some go to extremes like replacement of any boards.
Pc to tv
if you PC has one of the following outputs then it will work ...
composite (rca jack) , S-Video , HDMI or component (three wire rca jack) ...
several video cards have at least composit video out as well as the normal VGA output . look for a single RCA.jack ....
if your video card does not support any of these formats then you would need a VGA converter box to one of those formats ... there is also a USB to s-video/composite converter cable ...
the resolution of your set is 1024 X 768 ... so thats what you would set the video card for ..
Not finding what you are looking for?