20 Most Recent Dell 926 All-In-One InkJet Printer - Page 4 Questions & Answers

This is a "carriage timing belt" or in tech term's an "encoder strip". It reads the cartridge carriage when it moves left to right for positioning. Is either of the ends split or broken? If so, you are out of luck trying to reinstall it. I would recommend replacing your printer since this isn't a very expensive one. Just find a electronic waste disposal facility (or local E-waster drive at your nearest school, etc) or check with your city or state and find out where you can drop it off. Good luck.

Hi,The print head nozzles may be clogged. From the Utility section found in the printer driver, clean the print heads by performing a head cleaning followed by printing a nozzle check pattern. A head cleaning and nozzle check must be performed as a cycle. After printing a nozzle check, examine the printed dot pattern. Each staggered horizontal and straight vertical line should be complete, with no gaps in the dot pattern. If there are gaps in the dot pattern, continue with another cycle. Performing up to 6 cleaning cycles is not uncommon if the print heads are severly clogged.Now you will be able to print in colour.Hope this helps.Shane

theres an error on the printer head or ink dell printer

bring it to a service center, looks like a head problem that needs to be check by dell printers

its hard to explain on how to place it back, but try to remember on how you took out the old cartridge then reverse it. all it needs is a good push dell printer

try pushing it? try to remember how you took out the old cartridge then reverse it dell printer

do you have to copies of the same printer in control panels printer menu? dell printer

remove the tape from the cartridges, it has tape on the contact point of the cartridge, pull them out again and double check dell printer

you can try cleaning the paper guides with cotton swabs and alcohol dell printers

did the printer read the new ink cartridges? it does not produce an error? dell printers

take the cartridge out and put it back in, sometimes they don't line up right, or communicate properly with the printer, or there is a malfunction with the cartridge

Hi,if you have the users manual (given that it has worked properly in the past) my suggestion would be to disconnect the printer from the computer/uninstall the current software/then with your manual in hand follow the guidance PRECISELY to reinstall the printer. If you do not have the manual it can be obtained (free) from the Dell site. Just before doing the uninstall/reinstall if you haven't already done so you might go to the Dell download site and install the latest drivers for the printer from there.Hope this helpsThanksDennis

I was told by cartridge refillers that the level of ink will not be displayed for refilled cartridges.

You might have to uninstall the printer restart your computer then reinstall your printer click start control panel administrative tools computer management device manager scroll to ports(COM&LPT) + to expand you should see a communication port and Ecp printer port you might see a yellow? ! question exclamation mark or a red X this will mean you need to install a new driver for this device right click you will have options to update driver,disable,uninstall or select properties again you will have the similiar options also you can troubleshoot the device hope this helps you

Start, control panel, printers, your printer, printer preferences, advanced. Uncheck the complete-a-print boxes and also check to make sure the print in black & white box in unchecked.Rick

Using generic or refilled Dell Series Ink cartridges will always give the low ink message.To remove the message, try the Dell Series brand from Walmart Staples or Dell's website.Article on refilling Dell ink cartridges Rick

first try to powerdown your printer for like 15 secs...then power it on. now on your printer.. press the right arrow 3 times then press select.press the right arrow 4 times then press select press the right arrow 3 times then press selectusing the left or right arrows ..look for the language you prefer then press selectpress now the back button to return to the main menuRick

first try to power down your printer for like 15 secs...then power it on. now on your printer.. press the right arrow 3 times then press select.press the right arrow 4 times then press select press the right arrow 3 times then press selectusing the left or right arrows ..look for the language you prefer then press selectpress now the back button to return to the main menuRick