20 Most Recent Sylvania LC320SS8 32 in. LCD Television - Page 5 Questions & Answers

I have the same problem suposed to be blown capacitors but I dont see any so back to square one

good day . your tv has a defect . maybe i the main board causing not to switch on the power. just go to the sevice center to fix your problem

Yes, with a mounting kit. A plate screws to the TV using those holes, then attaches to another plate that's attached to the wall.

You have to use the buttons on the side of the T.V. through the picture menu.. There is an aspect ratio/ picture size option usually that will allow you to change it. You'll just have to learn how to navigate the menu with the volume/menu/channel buttons.

Try tv unplug,replug an hour later.The tv should reset it self and work.Not,than the power supply board is the cause,that the board,where the power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.

Have you tried googling the model number, funai is no help if you dont have a contract with them. Finding schematics for their powersupplies is hard, a majority of the time its better to just buy another ps because many of the parts they use wont cross to NTE. Are the voltages coming out of the ps just high? If they are one of the boards might be bad, I had a funai tv that had a bad board and was keeping the rest of the tv from powering up so the volatges I was getting were high due to the lower load. Also check for a schematic for that specific panel as funai uses LG panels in their stuff.

you have the refresh rate or the screen resolution set to a size not supported by the tv, change it to 800 x 600 and try it. If it works increase it till you reach the maximum that the tv can show

If you have connected the TV to the computer with a VGA cable, what resolution was your previous monitor using? You may need to change the resolution or refresh rate with your regular monitor attached. This TV has a native resolution of 1366 x 768 .

If you are connected via one of the HDMI ports, check the specifications for your TV. Then try using the VGA output. Not all TVs support a computer signal over HDMI. Unfortunately, I can't find the LC320ss8 at the Sylvania Support site: http://www.sylvaniaconsumerelectronics.com/ . If the model number has an error, click on Downloads and enter the correct model number.

I hope this helps.

Cindy Wells

We would be happy to help get your picture back. The first thing we want to ensure is that all connected equipment is on.Check what type of cable is used to connect the TV to the receiver. If you areusing a Coax Cable to connect the receiver to TV1, check the receiver'sback panel for the output name. If your receiver has a "TV CH 3/4Out" (non-ViP Receiver): Tune TV to channel 3 or channel 4, backif it is labeled "Home Distribution" (ViP Receiver): Tune TVto channel 62 or 75. If using non-Coax (RCA, Component, orHDMI) to connect receiver to TV1, cycle through the inputs until pictureappears; Most TVs have a "TV/Video", "Input", or"Source" button. We want to ensure that the TV and the receiverare connected properly, please visit this link to for more information:http://www.dishnetwork.com/SupportSection/setup-receiver-totv. Once we havemade sure everything is connected properly, unplug receiver for 10 seconds thenplug it back in, this will reset the receiver. If we are still not getting apicture connect another component (VCR, DVD Player, etc.) to the same TV, usingsame cable, same input, and same channel to see if it works. If you get apicture with the other component give us a call at 1-800-333-DISH (3474) forsome additional troubleshooting. If it doesn't work with the other componentthen replace the cable that was used.

We hope these steps resolve the issue. We want to thank you for being a valuedDISH Network customer!


Phillip Chang
DISH Network Customer Service Representative

Hello, this can be fix but know that Ur power supply board is dead, u know basic electronics’ and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get ur tv power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.
Hope this helps...

Hello

You can connect your Sylvania LC320ss8 to a computer. There is a socket at the back of your TV to connect it with a PC via VGA cable. One end of that cable must be connected to TV, and the other end of the VGA cable must be connected to PC's monitor out jack.. You have to purchase on VGA cable for this purpose, and is available at most of the electronic spare part shops. A "mini-plug audio cable" also is needed to connect the audio from PC to TV. Its one end to be connected to PCs Audio Line Out jack and its other end to TVs PC in audio jack. Both Jacks can be located at the back side of the TV. After connecting it select the TV to receive PC signals according to its manual says. OK.

i had my tv hooked up to my desk top pc then i had to unhook it and use a older monitor then i rehooked the tv back up and it said not support format

i think it can, just pair your tv and remote then insert the remote code, try it

After 4 months, I hope this has been resolved, but if not, or if you have any questions, here are some steps. Below are links from the DISH Network website. The first link is to a power scan, where the remote scans through all of the codes on the tv until it reaches the correct one. The second is codes for each brand of tv. If you choose to use the codes, you will need to follow these steps:
1. Hold down the TV button until all lights light up at the top of the remote.
2. Punch in the 3-digit number (code)
3. Press the pound (#) key on the numeric key pad under the 9.
4. Try to power the tv off and on. If this works, press SAT on the remote, if not, go back to step 1 and try another code.

Power scan:
http://www.dishnetwork.com/SupportSection/power-scan-instructions

Codes:
http://tech.dishnetwork.com/departmental_content/techportal/content/tech/remotes/TechRemo5.3Code.shtml


Becki Barned
DISH Network Customer Service

all you have to do is google the model of the remote and look for code list and find which cable box you are trying to use, wala

Please replace the batteries of your remote then retry

What is the brand of this universal remote control? Each brand has its own codes setup, we need more info to do the research for you.