20 Most Recent Spectroniq Protron PLTV-32 32 in. Plasma Television - Page 3 Questions & Answers

Do an internet search on the make & model TV for a manual.

Hi,

Before ordering a replacement remote make sure you have followed the troubleshooting steps provided in the manual, mainly:

1. Make sure the batteries are new and inserted and oriented properly.
2. Check whether any button is stuck.
3. Remove any obstacle between TV and remote.
4. Bring the remote closer to the TV.
5. Turn the TV off then on from the power button on the front of the LCD.

If you have tried these but still the remote does not work, there is a good chance it can be repaired. It can be as simple as a bad solder joint particularly where the batteries are inserted and/or a faulty IR LED. The LED is what emits the signals and is located in the center, front of the remote.

To check the IR LED, view the remote through a digital camera's LCD (you can use a mobile camera-phone) while pressing a button on the remote. The IR signals emitted cannot be perceived by the human eye but the camera will see it glowing. If it doesn't then its probably faulty.

After making sure the remote is the culprit, call on 1-888-257-8899 and ask them for a replacement remote.

Check your cables going from your DVD player to your TV to make sure everything is plugged in all the way and correctly. If the problem continues try a DVD that you know works and is a color movie and see how it plays.

Hi,
Symptom shows it is power supply board that need to be replaced in Spectroniq PLTV-3250 TV.
Click Shop Jimmy that has power supply board in stock for $94
Power supply board replacement is not so difficult work and if you are not comfortable with it, call local TV tech for board replacement.
Thanks.

I don't know what BOLT is, as I fixed my last DVD player 6 years ago at Sony. I think the Disney Format is Newer than your DVD player can read.

I remember Sony had a $5000.00 when new DVD player that was the first generation of DVD's. We would get them in for repair and the guy would say "My Radio Shack $99.00 plays all my DVD's but this $5K FIVE YEAR OLD unit won't play them....

There was NO fix for the problem. The New DVD's were beyond the capability of the 5 year old unit.

SO.. Is the Disney DVD a Blue Ray Disk? Or a new format that your older DVD can't read?

AL

The most obvious reason is an overheating issue in the Power Supply board. There are other ideas here, but you need to take it to a television engineer to diagnose https://www.google.com/search?q=television+will+suddenly+turn+off+every+4+minutes ..

Check the internet connection. The television can't update if it can't see the internet. Resetting it breaks the previous settings. Just for fun, reboot the router as well and wait 15 minutes until all the lights come back on. Then reestablish the television connection to the router. Harwa is not a make we know here in North America. https://www.google.com/search?q=Harwa+Smart+television.+How+to+restore+Apps ..

general steps: Get the TV remote control and push the "Menu" button and select "Options". Select "Child Lock" from the "Options" list. On some televisions, the "Child Lock" is named "V-chip". Choose the "Remove Child Lock" selection. Highlight this and then hit the "Enter" button. Enter the four-digit code that you used when you activated the child lock feature. If you cannot remember it, your only option to deactivate the child lock is to reset the TV. The instructions for resetting a TV is written on the user's manual of the TV. Exit the TV menu once you have entered the four-digit code. To do this, press the "Exit" or "Menu" button on the TV's remote control. If you don't have a remote, you might try leaving the TV unplugged overnight. Some TVs will 'forget' their settings if left without power for a long period. You could also potentially buy a cheaper universal remote, and use that to turn off the child lock.

To pair your Ruwido Amadeus R 9710 remote to your TV, you can follow these steps: Insert Batteries: Your remote is powered by two 1.5 V AAA batteries1. Make sure to insert the batteries correctly. Switch on your TV: Ensure your TV is turned on. Press the TV key: Press the TV key on your remote control for approximately 4 seconds until the LED flashes twice. Enter the Code: After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical code from the list provided with your remote2. After entering the code, the LED will flash twice indicating that the code has been accepted. Test the Remote: Point the remote control towards your TV and press the key. If your TV does not respond by going into Stand-By mode then repeat steps 3 to 5 and enter the next code in the list. Bed.-Anl. H2 Version1 (ruwido.com)

That sounds like it has a backlight fault. A good TV engineer can possibly repair that for you.

Ask your parents. There is no easy way to defeat the parental lock.. https://www.google.com/search?q=Tek+model+L26D10+TV+unlock+code ..

TV maker is Palladium codes are 0560, 398, 391, 446

Try cleaning behind them with electronics switch cleaner spray, but it may be the whole module is faulty. https://www.google.com/search?q=jvc+kw+av50+volume+button+not+working ..

Question edited for clarity. Question moved from Car Audio category. Help in the link https://www.google.com/search?q=Ecco+32+inch+smart+tv+lh32+is+showing+red%2C+blue%2C+green%2C+white+and+grey+simultaneously+when+I+turn+it+on ..

The axles may have substantial amount of in/out play, 1/4 inch or more. Does the axle in question actually drive the wheel or does it freewheel?It's a typical differential so if you get both wheels off the ground and spin one wheel, the other wheel should rotate in the opposite direction.The axles are retained by the differential assembly (inside transmission) so if the axle is truly falling out, to fix it will require transmission be removed and opened. Probably not an economical repair unless you can DIY or replace with good used unit.

Turn on your Sky Box and TV. On your Sky Remote, press the TV button. Simultaneously press the Select and Red buttons until the red LED on your remote blinks twice. Enter one of the following 3-digit remote codes for Sky TV: 2274 2169 1874 1798 1872 1873 The light on the remote should flash twice. If it blinks only once, repeat the steps with the next code. Press the Standby button on your remote. If your television turns off, press the Select button to save the setting. Turn on the TV and press TV Guide; if the TV Guide list displays on the screen, the programming was successful. Remember that there are multiple versions of Sky Remote Controls available, so ensure you have the most recent version. If you encounter any issues with the 3-digit codes, you can also try using a 4-digit code. Here's how: Repeat steps 1 to 3. Enter the 4-digit Sky remote code for your TV brand. Press the Standby button. If your TV turns off, press Select to save your settings. Check if the TV Guide displays successfully on the screen. Sky TV Remote Control Codes

To update the software on your Harwa 32-inch TV, follow these steps: Check Other Solutions First: Before proceeding with a firmware update, ensure that you've tried other troubleshooting solutions. Sometimes issues can be resolved without updating the firmware. Gather Necessary Items: You'll need the following: A computer with an available USB port. A high-speed internet connection. A USB flash drive. Find Your TV Model Information: On your TV, navigate to the Help menu and select System Info. Write down your TV's model, revision, and firmware information. Download the Firmware Update: On your computer, visit the Insignia Products website at www.insigniaproducts.com. Click on Support & Service. Enter either NS-19D220NA16 or NS-19D220MX16 in the search box under Manual, Firmware, Drivers & Product Information. Follow the Firmware Installation Guide: Download the firmware update from the Insignia website. Copy the firmware file to a USB flash drive. Install the Update on Your TV: Plug the USB flash drive into the USB port on the side of your TV. Press the MENU button on your remote. Navigate to HELP and press ENTER. Highlight Update Firmware and press ENTER. Confirm that you want to update the TV firmware by selecting OK. Your TV will display a status screen while installing the update. Do not turn off your TV during this process. Once the update is complete, unplug the USB flash drive and press ENTER. Your TV will turn off and then back on to finalize the update. Rescan for Channels (if needed): If your channel list has been deleted, you'll need to scan for channels again. Refer to your TV's manual for instructions on how to do this. Remember: If you encounter a message saying the firmware file is incorrect, ensure you've downloaded the correct file for your specific model. If the update fails or your TV screen remains blank with a blinking red then blue power LED, turn off your TV, turn it back on, and run the upgrade again.

Sorry, we do not supply anything. I would aproach the supplier or manufacture for advice and spares availability.

Sorry, but we do not supply parts. This is a website for advice on repairing items. You could try contacting the store you bought it from or contacting iheater directly.

It appears that there could be miscommunication. As of my previous update in January 2022, Matertech doesn't seem to be a commonly known term or corporation. On the other hand, if you're talking about "Google," it's a well-known worldwide technological corporation that specializes in internet-related services and goods, such as search engines, cloud computing, online advertising technologies, software, and hardware. Google's official website or an internet search utilizing one of the search engines like Google itself are usually the easiest ways to get information about Google. If "Matertech" relates to a particular thing or idea, further information could be helpful in order to provide a more precise answer.