LG 50PC3D 50 in. Plasma Television - Page 2 - Answered Questions & Fixed issues
Turn on and red light go to green and back to red
These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit stage inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power led, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating, to many popular brand TVs and other devices. Viewing it in "
Mosaic" will make surf easy.
http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given.
Wont turn on when u press on off button it just goes click click clickc
Go to EBAY and look up a capacitor repair kit for your model kit. They cost $20 to $30. This is to fix the power supply board which is the middle board. Be sure to note polarity of the capacitors you replace. There is a positive and a negative on them and that must be observed. Use a magic marker and mark the top of each cap as you replace it. Replace all caps supplied in the kit even if old ones don't look puffed out. This should fix your power supply. I did this on a friend's set over a year ago and the power supply is still ok.
TV won't turn on at all, totally dead.
Check and replace its main power supply regulator board as card basis. Normally, there is no repair to these boards of plasma TVs. Any attempt to repair this board, will result both waste of time and money. And more, after replace this board, you have to adjust the Vs & Va voltages, according to the plasma panel label too. In fact, replacing this board is not a silly work for a user to proceed. It will be best to contact any service technician. If you wish to get some details; check the site linked here. Viewing it in "
Mosaic" will make surf easy.
http://electronicshelponline.blogspot.com/
Error codes table
If
you wish to get more details, check this link.
http://electronicshelponline.blogspot.com/ Selecting the view option, either to
Mosaic
/ Time slide, can be selected by the
drop-down list, at the top left
of the display window, will make surf easy. You can also do a search, by type in the brand name/model
number/IC used, in the search box at the top right of the display window.
LG 50" Plasma / Flickers with vertical lines also
There are so many reasons for this fault. If you wish to get more details, check this link. It has screen-shots illustrations to faulty screens to plasma displays. You can see and compare it to your TVs' and can make sure about the faulty section circuit inside it.
http://electronicshelponline.blogspot.com/
Pull up previous posts by its left sidebar, or type in the
brand name and model number to of your set, to its search box, and
press '
Enter' or view it in
Mosaic / Timeslide
option.
Is it safe to repair a plasma zsus board yourself?
You need to be careful around the capacitors as they can definately shock you. But if you have diagnostic and soldering experience its possible to repair the board. However schematics for those boards are almost non existant since they were designed for board replacemet repairs only. But for most its easier to just replace the Board. You can get most boards from
www.tvcircuitboards.com and they can assist with installation instructions usually.
Lg 50 inch plasma 50pc3d-ue sound but no picture
Visit the site named '
Electro-help' for
more details. Click this
link. View it in
"
Timeslide" option, which can be selected from the drop down box
menu by the [
Sidebar] tag, at the top left corner of the display
window. It will make search easy. There
are more than 1100 posts to different brand TVs now. Pull up older posts there. Sometimes, you might repair it by yourself. It is very difficult to describe all details with illustrations here by this window. Checkout patiently.
Dim/dark screen on my lg50pc3d tv
After its on for 15 minutes, feel the heat sinks on the y board ( on the far left side) if they are cold then replace that and the upper and lower drive boards that attach to the Y main.
Lg plasma menu screen wont go away
The exit button on the remote may not be working or some other button on the remote is jammed. Try removing the battery of the remote and switch off the TV manually and the input power. Wait for a few minutes and then switch on the TV manually. The try changing the menu from the TV control panel. If nothing works, this is a case to be handled by a qualified service technician.
Not finding what you are looking for?