Konica Minolta Magicolor 2530 DL Laser Printer - Answered Questions & Fixed issues

check the media Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Service manuals electronic components datasheets and equipment schematics... try this site for manual Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

check your media guides and check the user setting of the printer at the printer and compare at computer printer properties Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the fuser unit. and replace the transfer roller and belt, Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

got a bad one replace it try this site for parts as a start Precision Roller Printer Toner Cartridges Parts and Supplies Office... Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

try this site Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace with a new one. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the fuser unit Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

what do you mean not straight?? the document come out skewed? if so check the rollers for that draw also might be something in the paper path the paper hits causing it to skew Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

try this site Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

the laser is being blocked for that color remove the image units and clean the slit glass that the laser goes though Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

check and make sure correct media is selected in print properties and select at the machine Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

The transfer belt is what places the image on the paper, which the belt receive from the drums. Get a new one or re-install the belt properly. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

On windows it is ok? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

I literally just fixed the same problem in my 2530DL. Look at section 6.3.23 in this service manual for a nearly identical model http://printer.konicaminolta.com/drivers/other/Manuals/24_25/fs_2400s.pdf and notice the "Precaution for Reinstallation" This Registration Roller Solenoid is an electromagnet-activated lever which controls the timing of the page's movement through the printer. The manual notes that the space between the "flapper" and gear is critical for proper timing. In my case, the tiny foam pad at the bottom end of the flapper had apparently become compressed over time, resulting in the spacing going out of tolerance. I removed the foam pad and replaced it with layers of electrical tape, adding layers until I found the thickness needed to make the printer work correctly (6 to 8 layers). Then I removed the tape and glued in a piece of hard rubber of the same thickness. (Tape is only a temporary measure as it can compress or become sticky after a while.) Everything is back to normal now! Good luck!

Verify the printer paper size settings and on PC the paper layout settings.

GO HERE FOR DRIVER onyxweb.mykonicaminolta.com/OneStopProductSupport?appMode=Public CANT PUT IN FULL LINK WONT POST

Thank you for your kind reply.I'm not going by the readout - but by the fact that bits of paper get stuck under one or two of the final feed rocker/rollers,,,, and are a bu@@er to get out.Kinolta Customer Service - AND MANAGEMENT - are aware of just how badly designed this paper feed system is, but will do nothing about it.I have had to virtually strip this piece of carp down, just to give me a little more access,,,, even then, its more than a struggle.Thanks again.

This is so very common with these machines. Unfortunately, you can damage the roller just underneath the paper feed if you aren\'t careful. Konica know that this problem persists, but will do nothing about it. Their Customer Service - as well as management - gets very rude and quite offensive when questioning them on the subject.I virtually have strip the thing down, just to clear bits of torn paper - too often.I won\'t buy K.Minolta stuff again.Good Luck

C 0010H - Color PC drum malfunction.Check the motor for proper drive coupling and correct as necessary.Check the motor connector and the electrical board connectors and the mechanical transport drive components(gears,couple).