Top 20
HP LaserJet 4350dtn Printer Questions & Answers
How to solve hp laserjet 4350dtn fuzzy print?
usely it's the fuser sleeve the problem. replace the fuser but before be shure the cartridge is ok. print something and open the cartridge door when printing to see under the cartridge the print quality if ok replace the fuser unit
HP LaserJet 4350dtn
Typically the only reason that a printer beeps when printing is because you have the printer plugged into a UPS. None of the circuit boards on the 4350 have any sort of audio capability. Plug the printer right into the wall outlet.
60.20 error
The tray 2 lifter-motor is not functioning
Unfortunatly this usually requiers parts
1 Turn the printer off and then on.
2 If the error persists, turn the printer off.
3 Verify that the tray 2 lifter wire-harness is full seated in its connector on the dc controller PCA (location J93).
4 Replace the tray 2 lifter-driver assembly
-If the unit is still clicking/banging with a new lifter replace the tray
-If the unit is still clicking/banging with a new lifter and tray see step 5
5 Replace the dc controller PCA.
Service Error 49.4CF2
Usual solution is to update the firmware of the printer. The quickest solution is to use a different printer driver. So if using PCL, try Post Script (or the other way around).
50.2 fuser fault on a
Indicates that fuser is not cycling properly. Usually caused by a failed fuser. If your page count is anywhere near 200,000 pages, your best bet is to purchase a maintenance kit which will come with a new fuser, as well as the feed/separation rollers.
4C02 Service error?
49.XXXX PRINTER ERROR
To continue turn off then on
No error message will be in event log.
A critical firmware error has occurred that caused the processor on the formatter to abort operation. This type of error can be caused by invalid print commands, corrupt data, or invalid operations. In some cases, electrical noise in the cable can corrupt data during transmission to the printer. Other causes include poor quality parallel cables, poor connections, or homegrown applications. On rare
occasions, the formatter is at fault, which is usually indicated by a 79 Service Error.
1. Press CANCEL JOB to clear the print job from the printer memory.
2. Turn the printer off and then back on.
3. Try printing a job from a different software application. If the job prints, go back to
the first application and try printing a different file. If the message appears only with a certain software application or print job, contact the software vendor for assistance.
4. If the message persists with different software applications and print jobs, disconnect all cables to the printer that connect it to the network or PC.
5. Turn the printer off.
6. Remove all memory DIMMs or third-party DIMMs from the printer. (Do not remove the firmware DIMM in slot J1.)
7. Remove all EIO devices from the printer.
8. Turn the printer on.
9. If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and back on as you install each
device.
10. Replace a DIMM or EIO device if you determine that it causes the error.
11. Remember to reconnect all cables that connect the printer to the network or computer.
12. If the error persists, replace the firmware DIMM.
13. Replace the formatter and calibrate the printer. See Calibrate now.
Why can't I print dual
If you go to PRINTERS in the Control Panel.
Right click on your printer.
Drill down to PRINTING PREFERENCES
Go to FINISHING.
Make sure that "print on both sides" is checked.
Close that window. Now drill down to Properties at the bottom.
Go to "device settings". Drill down to "installable options".
Make sure that "Duplex Unit" is INSTALLED.
Print out the CONFIG pages. On the first page right side, look for duplexer. I believe that it is down where the paper trays are listed. Make sure that it is there.
Hp Laser Jet 4350dtn network
Does it occur on any print job or one in particular. If it happens with one job, that job has a problem. It isn't the printer.
If it is all printing go the www.hp.com. then go to "support and drivers". Then select your printer, select your operating system, select firmware. Upgrade your firmware. Make sure that you read the instructions and DO NOT touch the printer while it is upgrading.
If the firmware upgrade completes and the errors continue, you will need to replace the formatter.
I have HP Laser 4350N,
Usually printers receive and store jobs to be printed on the device before they actually print the documents which should be printed. if queued jobs are a lot on the printer it could have problems of slow printing but being that the printer is on a network this seldom happens as documents will be processed with precision.
Another thing which could cause slow printing is a low level of ink in your device. If the level of ink in the cartridge is low the unit will find it difficult to pump the ink for printing and therefore bring about sluggish printing.
Although 12 pages per minute is not so bad a speed for the printer to run as it is a heavy duty machine.
Hope this solution has been helpful?
When i on the printer
The
HP Print Diagnostic Utility might not be available for all HP products,
particularly older products. It is available for most products,
however, and in most languages. This tool is available only for Windows
operating systems.
-
Right-click the following link, and then click Open in New Window
.
Link to tool
(right-click)
File size
HP Print Diagnostic Utility
1.51M
-
Make sure your computer meets the system requirements, and then click Download
.
-
When the Security Warning
dialog box opens, click Save
. The Save As
dialog box opens.
Important: HP recommends that you save the download according to the
following directions to ensure that you can easily access the tool again
at a later time.
-
Click Desktop
, and then click Save
. The Print Diagnostic Utility is now saved to your desktop so that you can access it any time.
-
When the Download Complete
dialog box opens, click Run
, and then click Run
again on the Security Warning
dialog box.
-
When the tool finishes installing, click Finish
. The Print Diagnostic Utility opens automatically with a list of installed products.
Hi i got 49.4co1 and 49.5001 error on my printer. ...
The P3005 is known to have problems with a chip on the formatter, gives
various errors to include the 49.2d9d, blank display and others. HP has
not issued a recall or service advisory but is fully aware of failure
of the chip on the formatter. Repair for this is to print a
configuration page, replace the formatter board, bring the machine back
up in service mode and put in the correct serial, service code and page
counts into the new formatter's nvram memory.
Liberty Parts Team
at lbrty.com has refurbished formatters at reasonable pricing with no
return core to worry about. The PIN needed to access the service mode is
10300506.
Other problems with the P3005 are grinding in the
fuser area, correctable by removal of the fuser, replacement of the 4
accessable gears in the side (left as you look into the back) and the
main gear on the fuser then put the fuser back in and should be good.
Service
manual available for free at feedroller.com - down the left navigation
bar near the bottom is an icon and link to service manuals in PDF. No
need to make someone on ebay rich selling copyrighted pdfs.
Not finding what you are looking for?