20 Most Recent HP LC3760N 37 in. LCD HDTV - Page 9 Questions & Answers

Usually means you need to update your video driver. What model is your computer you are connecting the monitor to?

This sound like the power supply board has failed. The electrolytic capacitors on the board may need to be replaced. IF YOU KNOW HOW TO WORK WITH ELECTRONICS REPAIR(soldering ) or have a friend with knowledge/skill you can fix it. >Unplug the set. >Remove the back cover. >look at the capacitors on the power supply board. If the top of any of them are bulging up that is the problem. >You will have to replace ALL the electrolytic capacitors except for the large one.> Use ones with the same farad rating > Use ones with the same or higher voltage rating> Use high temperature rating> Install one at a time to prevent mix-up and keep the polarity correct. > Leave a space between the PC board and the bottom of the capacitors for expansion. They heat up.THIS IS AN INDUSTRY WIDE PROBLEM AFFECTING MANY COMPANIES AND PRODUCTS. One source for some good capacitors is NTE. Try nteinc.com for a local outlet.You can also search for other sources. Some companies even sell all the capacitors in a kit. Total price of parts should be < $20.00

Hi,
I'm assuming that your unit is dead seat.

Here are some DIY steps that may help you fixing the problem.

1. Check the power cord - check the cord it might be opened (no continuity).

2. Check the internal fuse - sometimes the fuse fail because of the power surge, replacing with new one will cure the problem, If this is the case I've advice you to use surge protector/AVR (Automatic Voltage Regulator). However if the fuse blew again this is an indication that you have a shorted parts on the power supply, you may visit the link http://www.fixya.com/support/r8053361-fuse_keeps_blowing for more info. If no reaction and still the unit didn't power up then you have an open parts on the power supply.

3.If you see that the fuse is intact on the board, don't attempt to touch anything because there some fatal components stored electricity enough to hurt you with a simple mistake only.

The next steps should be done by an expert or qualified technician because isolating the problem on the power supply is quite technical.

Also check if your unit is under warranty before opening the back panel, it will void the warranty. Avail it because the manufacturer of your unit will fix it for free or a little charge only.

Hope it may help you.

Thanks for using fixya.

JDVillanueva

Hello
You have to replace or repair the adapter.
Good Luck

There is a good chance one of the projection bulbs blew and it's in shutdown, but you should take to a qualified servicer to verify. If so, bulbs are available here: http://www.electronix.com

OSD means On Screen Display. To unlock the OSD hold the power button of the monitor until you get a message similar to "OSD unlocked".
If you still have problems, click on this link for further instructions :-
http://www.ehow.com/how_5008634_fix-lockout-display-computer-monitor.html

It allows you to view the digital HD channels that can be received with a simple tv antenna like the ones from Freeview on your pc.

power supply faulty get hold of hp support they will let you know where the closes repair shop is

Try HP Support & Drivers

Hello.
You probably did not have that tv plugged into a surge protector. When the power was restored, a surge came through the line. A power surge is a spike in voltage above the maximum a tv, appliance etc. can handle of 169 volts. They are very brief, usually lasting millinths of a second. Power surges can vary in duration and magnitude, varying from a few hundred volts to several thousand volts.

That said, now what do you do. If the tv is under 3 years old I recommend that you take it into a local TV repair shop for a free estimate of repair. If it is older than that, I would not repair, just replace. J.

Hello ma'am, you HP has power supply problems. this requires replacement of the board. If you have no idea, call for service.

Either someone is messing with you or the control processor is faulty.
Simple test: block the remote sensor in the front of the tv with a dark coloured tape. If you still have the same problem then the processor is faulty and the entire board will have to be replaced by the dealer (or an authorized repairman).

Clean the lenz if this doesnt solve it your Laser Pick Up assembly is bad have a Tech replace.