Top 20 HP Photosmart C5180 All-In-One InkJet Printer Questions & Answers

Hi, try to install drivers via web install download manager directly from official HP site. Good luck!

Most probably caused by a power supply failure or main board short. Either way it is not a repairable fault.

Go online to the HP store. Enter the model number of your printer plus the part you need. I've used this site a few times myself and have had excellent results.

Have you tried highlighting just the lines or paragraph you want to print. That may help.

Load the printer with the slick glossy paper face down. See if it will print.

HP has a problem solving or troubleshooting software you can use. Also maybe your port settings changed. 168.06.01 is a typical port. Check that. Also use the WPS method to connect.

Switch on the printer. Halt a minute until the device is idle. Unplug the USB cable from the printer's rear. Look at the connection method. In case it is wireless, examine whether the printer is linked to a wireless network. Take out the ink cartridges from the printer. With the printer switched on, unplug the power cable from the printer's rear and wall socket. Wait a second and then connect the cable back to the printer. Now, examine whether the issue persists. In case it exists, upgrade the printer 's firmware to the recent version. 123 hp com Quick HP Printers Setup Easy Installation Guidelines

In case you are not able to place the paper pick up roller to its slot,call the printer technician to solve the issue. Toll Free No 1-888-224-4280 123 HP COM Setup Printer Quick Setup and Install Support

It won't turn on just repeatedly on and off - HP Photosmart C5180 All-In-One InkJet Printer Check if the power cable is working correctly. Try to connect the printer using a different cable. If the issue persists, move to the next step. Connect the printer straight to a wall outlet rather than connecting to a surge protector. For Quick printer support Call Our Toll-Free 1-866-293-9220

your ink might be getting finished.try to refill or replace cartridge..thats all..

A few things to try or consider: 1) Has the Magenta ink cartridge expired? 2) Is it a genuine HP cartridge? 3) Is the nozzle plugged? 4) Did you allow the printer to run completely through its maintenance cycle? 5) Did you print a test page? or is this the "diagnostic page" you mentioned?

HP Printers Problem with Printhead Printer Failure Ink System Failure or...

a4 paper works normally remains 5x7 paper tray or if it remains stuck in the printer tray rollers that pull the paper check is not dirty you can clean with water and a cotton ear

That is a Ink System Failure Code. The best you can try what is offered below from HP. You cannot remove the printhead so if the reset does not work, you will need to take it to get serviced. Fault code on the printer is 0xc18a0401

Before jumping into resolving the issue, assuming a technical failure, make sure the Auto-off feature on your printer is not enabled. This feature, in order to save power, turns off the printer automatically after a set period of inactivity.1 Check the Scheduled On and Off or the Auto Power Off feature on the control panel of the printer.2 Alternately, you can check the feature through the printer software installed on your Windows operating system. Open HP Printer Assistant, and give a double-click on the Maintain your printer option.3 Click the Advanced Settings tab in the Toolbox window. Change the settings if necessary and follow the prompts on the screen.When you are sure that the Auto-off feature is not the cause, try carrying out the steps given below.1. Restart your printer• Turn on the printer and give it some time to become silent.• Unplug the power cord from the printer. The printer should be turned on while unplugging the cord.• Remove the power cord from the electrical wall outlet.• Wait for at least a minute and reconnect the power cord to the wall outlet and to the printer's rear.• Turn the printer on if it does not automatically turn on.• Wait until the printer is idle and check if the issue is resolved. • If the printer shutsdown again, continue with the steps.2. Update the printer firmware• Check if the printer is properly connected to your computer.• Go the manufacturer's website and click Printer.• Enter the printer model and click Submit.• Select the version of your operating system and click Change.• Select Firmware and click Download. If you do not see a firmware section, there is no update for your printer.• Save the downloaded file to a storage location on your computer and run the files.• Look for the printer's serial number in the HP Printer Update window. • If the printer's serial number is displayed, click the checkbox against it. Click Cancel if the status is 'not applicable'. If you have set up the printer on a wireless network and the serial number is not displayed, connect the printer and your computer using a USB cable, wait for about 20 seconds and Click Refresh. Once the printer's serial number is displayed, select the checkbox beside it and click Update.• Click OK once the update is complete.• Remove the USB driver installed on your Windowsif you have connected a USB cable to update your network printer.3. Make sure the printer is directly plugged into the power outlet• Turn the printeroff.• Unplug the printer power cord from the power strip or surge suppressor.• Check for any wear or damage in the power cord.• Wait for at least 30 seconds and plug the power cord directly into electrical wall outlet.• Power on the printer.4. Check if other devices are not causing the issue• Disconnect the USB hub from the printer and connect the USB cable directly to the printer and computer.• Remove any memory card or USB drives from the printer.• Restart the printer.5. Connect the printer to a different electrical outletUnplug the power cord from the printer and an electrical wall outlet, and reconnect it to another electrical outlet.6. Try replacing your power module7. Service your printer If all the preceding steps did not help, contact your manufacturer to get your printer serviced. for HP Printer support Call Our Toll Free 1-866-293-9220 or visit 123 hp com setup Support Free Driver Download 123 hp com Wireless

If the printer is about 1 year old or older, you may have bad printheads. Make sure you use OEM cartridge for this. If it is a newer printer, you may have a bit of paper stuck somewhere in the feed path.

Ink system failure is mostly caused by print heads. i do apologize but with issues like this, the best resolution is to replace the printer. it will only cost you buying new ink cartridges but it will not resolve the issue. :(

The printer's control panel displays alphanumeric code error without any additional information on the cause of the error. Carryout the steps below to resolve the issue. Reset the printer 1. Power up the printer and wait until it is idle and silent. 2. Do not disturb the wireless connection if the printer is connected to a network. 3. If the printer is connected to your computer using a USB cable, unplug the cable from the printer's rear. 4. Remove the ink cartridges from the printer. 5. Plug the power cord out from the printer while the keeping the printer turned on. 6. After a minute, plug the power cord back to the wall outlet and into the printer's rear. 7. If the printer fails to power on automatically, press the power button to turn it on. 8. Reinstall the ink cartridges. 9. Print a calibration page if prompted. 10. Plug-in the USB cable back to the printer if you unplugged it. 11. Try to print. Service your printer

1. resetting the printer did not resolve the issue and the error is displayed again, contact the printer's manufacturer and get your printer serviced. Do not forget to claim a free service if the printer is still under the warranty period. Call our Toll-free to get HP Printer Support 1-866-293-9220 http://ww123hp.com/

check 32v and 16v power supply if it is ok , take a part the printer and check the motherboard have not swollen defective capacitor

The 0xc18a0206 error code indicates that there is a fault with the ink cartridge. Follow the guidelines given below to resolve the issue. Replace the old ink cartridges with genuine ones. 1) Turn the printer on.Wait until it is silent. 2) Place plain paper in the input tray. 3) Lift-open the cartridge access door. Wait until the carriage moves to the cartridge access area. 4) Push the ink cartridge down to release it and pull it out from the slot. 5) Remove the plastic tapes from the ink cartridge. Do not touch the nozzles or electrical contacts. 6) Insert the new color ink cartridge into the left slot and the black ink cartridge into the right slot. 7) Close the in carrtidge access door and wait for the printer to begin the initialization process. 8) The printer prints an alignment page once the process is complete. Scan the page to align the ink cartridges. Reset the printer ? Power on the printer and disconnect the USB cable from the printer. ? Remove the ink cartridges from the printer. ? Unplug the power cord while the printer is still on. ? Reconnect it to the printer after about 60 seconds. ? Wait until the printer is silent and idle. ? Reinstall the ink cartridges and print a calibration page if prompted. ? Connect the USB cable to the printer and try to print. Service your printer If the issue persists, take your printer to the manufacturer for a service. Call our Toll-Free 1-866-293-9220 or Visit http://123-hp.business/