Lanier Compatible Copier Toner Black For 6112 - Page 9 - Answered Questions & Fixed issues

The polygon mirror motor (laser motor) is shot, and needs to be replaced.

The switch that detects the open cover is probably broken or stuck. Do this. Lean / press on the cover while trying to copy. Does it work then? If it does, you know for sure that the switch is stuck. If it doesn't, the switch is broken.

How to find this switch? Is there a small plastic tab on the cover that goes into a hole that you can see? Those are usually where the switches for such covers are located. Spray some electronic parts cleaner down this hole (available at auto parts stores). See if this helps any.

Bilal Hassan
Clarksville, MD

No, you can't reset. You'll need a tech. Here's what the manual says: Symptom (SC101) - Exposure lamp error - The standard white level was not detected properly when scanning the white plate. Possible Cause: ? Exposure lamp defective ? Lamp stabilizer defective ? Exposure lamp connector defective ? Standard white plate dirty ? Scanner mirror or scanner lens out of position or dirty ? SBU defective

send me an email address and i'll send you a copy

"user tools"
"Counter"

LD unit problem, or laser sync detector....requires a tech for sure.

open right cover, and front cover. Remove toner bottle assembly (not just bottle), unplug drum (photoconductor) connector. Press the gray/silver release tab and slide out drum. Install and plug in new unit, replace toner assembly, close covers, and the new unit is automatically detected and calibration will begin.

Hello sir; Just follow my direction, it will reset your machine;
1, press "clear mode", "107", then press and hold down "clear/stop" key.
2, touch "copier SP" on the screen.
3, enter "5810-001" press enter.
4, set value to 0, then turn power off and back on again.

Hello sir; According the menual said, that's thermister open or power supply board, but before go that far why don't try to do a reset, steps as follow;
Press "clear mode", "107", then pres and hold down "clear/stop" key, then choice "copier SP" then enter "5810" press enter, select 1, then press"R/#" key and "original type" key at same time to reset, try it and let me know the result. after reset just turn power off and back on.

Open the machine and to the right under the drum you should see the the black powder (toner) going down into container the right lower side  cover must come off. probably a service call will be needed

It could be that the black developer unit is clogged. The toner low sensor is located in the black developer unit. A trained copier tech may be needed to troubleshoot this.

I believe that model is a Richo in a disguise.... To get into service mode, first press the yellow C/A botton, then the numbers 1 - 0 - 7, then press and Hold the red C/Stop botton for a few seconds and the display will change. Then you are in the Service Mode... Good Luck

You didn't list a model, and I assume that you mean "SC405". That relates to a transfer belt problem -probably the clutch, depending on the model. It will require a tech

Reboot the machine first. If that doesn't work, go to user tools - system settings - file transfer or interface settings (depending on the model) and enter and admin email address. Then go to admin tools and tell it to auto specify a sender. It is looking for who is sending the scan, not who is receiving it...

Try this press the "yellow/ca" botton, then enter 1-0-7, then press and hold the "red" stop" till the display changes. Once, it changes turn the Main power switch OFF. Not the one on the control pannel. Let it power down then turn it back ON. If the problem is still there try to turn the copier Off again and unplug the sorter/ finisher and turn the copier back ON. Is the problem gone, if so you may have to get a service person come in and repair the sorter. Good Luck.....

Should be as follows:
"User tools"
"system settings"
"key Operator"
"program/ change/delete address"
Then select the appropriate function /address, etc. to change

Please let me know

Goto my website and Download the file from the Public Folder. It is the only Point 2 Point in the folder.

Do not forget to vote Yes or No if this information was helpful


www.copytech21.spaces.live.com

AC charge output error for k. OPC problem, bcu bad or hvps bad. Could be bad drum ground.

I'm going by my own memory here, so you may have to fool around a bit, but this should help. Manual is hard to come by for this old beast.

"user tools"
"fax"
Scroll to "key op. settings" (i believe you have to press "yes" or 'Ok" immediately after selecting this to access this feature??)
In there you should see settings for RTI/TTI. This is what you program for your Identifiers (use the 'quick dial' keys for entering text).

Good Luck ;)

you need to remove the drum unit out of the machine,and take cotton rag use achohol ..rotate the drum clock wise until you see the label that stuck on it..
good lock