Lanier Ld445c Ld435c Ld430c Ld425c Ld420c Newdrum Kit - Answered Questions & Fixed issues

in bypass put envelopes in short edge first, push the # button, select size of envelopes and OK it, (needs to be told of size)-Carl

You have to set up the settings in user tools on the operation panel.

after refill the toner may be bias charging roler is not proper fiting or toner cartridge is not proper insert

Fuser pressure error, service call

This problem is referred to as color to color alignment. Most color laser systems have a rough adjustment by means of a screw somewhere and a fine adjustment that is done in diagnostic mode as part of a setup routine. Try the latter first by locating your manual and looking through the troubleshooting guide which should explain how to force the machine to do an automatic color alignment. Your manual should be available online from your manufacturer's web site if you can't locate it. If this doesn't work you will need to take it in for servicing unless you are handy with tools and can find a service guide for your model.

Roger's post had to be deleted. We do not permit phone numbers. This what the manual says https://www.manualslib.com/manual/91372/Lanier-Lp222cn.html?page=480&term=Adjusting+The+Color+Registration&selected=1#manual More here including CopyTechNet https://www.google.com/search?q=Lanier+LP222cn+Color+Registration++Error ..

the problem is the model number mp ld425c from researching you need to search on mp c2500 replacement drum or see https://discountcopiercenter.com/ricoh-aficio-mp-c2500-drum-units/ suggest contacting the above company to see if lanier was taken over by ricoh as this sometimes happens and the ricoh part may suit your printer

Question moved to Lanier Copier https://www.fortwayneprinterrepair.com/wordpress/2016/10/09/5222-sc320-error-code/ https://www.google.com/search?q=Lanier+5222

see https://www.fortwayneprinterrepair.com/wordpress/2016/10/09/5222-sc320-error-code/

There are site here that say they have it. First on is a full description by Wichita State Court. https://www.google.com/search?q=lanier+lcr-5+manual ..

IF YOU CAN NOT REMOVE IT TO DUMP THE STUFF THAT IS IN IT OUT I WOULD SAY YES GET A NEW ONE

https://www.youtube.com/watch?v=Ct6ADVdtBIg

Then you can't.

All printers are not equal. Some utilize cartridges with ink reservoirs and print heads all in one. Some only have a Separate Print head carrier with a main print head and slots for ink-filled reservoirs. You can purchase and use less expensive cartridges from on line vendors. If you elect to refill carts, be prepared for a messy venture. What many printer users fail to recognize, is the print heads do wear out and prior to complete failure, the heads either cause streaking or poor color density. To clean a print head, run under the tap for a few minutes, very hot water on both sides , metal bars and where the ink enters. When all signs of ink have vanished, replace in the printer. Do not touch metal contacts as oil will interrupt electrical communications. Do a printer test and alignment. Should work.

http://www.productmanuals.org/lp/?brand=Lanier&utm_source=adcenter&utm_medium=cpc&utm_term=lanier%20manual&utm_network={}&utm_campaign=FM+Brands+02-03+2

Are these new or refilled?

Check on mfg site for reset procedure on printer.

It's most likely your Laser diode (LD unit). You're going to require a tech...see the posts the following link for the same problem. It's for a Ricoh model, but your machine actually is a Ricoh Machine (Ricoh owns Lanier), and is virtually identical to this one -just a generation older.

http://www.fixya.com/support/t1936988-sc_326_322_329_in_af2045

heres a good try...works 90% of the time....unplug machine for 10 mins and restart...hopfully this will clear the error...GL my friend

download the manual and read page No. 80,81 and 82 for scanning detal. http://support.ricoh.com/bb_v1oi/pub_e/oi/0001047/0001047863/VM1438632/M1438632.pdf