20 Most Recent
Toshiba e-Studio 3040c RADF Assembly OEM - RADF-Assembly-e-Studio-3040c - Page 3 Questions & Answers
Toshiba 307 model photocopy Machain Error Code 0008
Error code 0008 on a Toshiba 307 photocopier typically indicates a problem with the fusing unit. This could be caused by a malfunctioning thermistor or a problem with the fusing lamp. It is recommended to check the fusing unit and replace any faulty parts. If the problem persists, it may be necessary to call for service from a qualified technician.
Error code C380 paper feed failure
c380 indicates auto-toner error for black developer (K).
Check following:
Is the harness between the LGC board and the developer unit drawer connector open-circuited?
Is any harness inside the developer unit or the auto-toner sensor harness open-circuited?
Is the auto-toner sensor connector or the connector CN341 on the LGC board disconnected?
IF connector no problems, then u probably need to replace the auto toner sensor.
F 101 13 toshiba error code 4508a
The error code F101 13 on a Toshiba e-Studio 4508A printer indicates that there is a problem with the fixing assembly. This can be caused by a number of issues, including a malfunctioning thermistor, a problem with the heating roller, or a problem with the temperature control system.
Here are some steps you can try to fix the error:
- Check the thermistor: The thermistor is a temperature sensor that is located near the heating roller. Make sure that the thermistor is securely connected and not damaged.
- Check the heating roller: The heating roller can become worn or damaged over time, which can cause the error. Inspect the roller for any visible damage and replace it if necessary.
- Check the temperature control system: Make sure that the temperature control system is functioning properly and that the temperature is set correctly.
- Restart the machine: Try turning the machine off and unplugging it for a few minutes before restarting it. Sometimes this can clear the error.
- If the error persist after trying these steps, it's likely that there's a hardware issue in the fixing assembly that will need to be repaired by a service technician. They will be able to diagnose the specific issue and repair or replace the necessary parts.
It's best to refer to the service manual of the copier/printer or consult with an authorized technician before taking any steps. An unexpected move may cause further damage.
Toshiba e-studio 452 error code c010 how to solved it
Error code C010 on a Toshiba e-studio 452 printer indicates a problem with the printer's fuser unit. The fuser unit is responsible for bonding the toner to the paper and can become damaged or worn over time.
To troubleshoot this issue, try the following steps:
- Restart the printer: Turn the printer off and then on again to see if the error message clears.
- Check for any visible issues: Inspect the printer and its components for any visible issues that may be causing the problem. This can include debris or foreign objects that may have gotten stuck in the printer, or damage to the printer or its components.
- Check the fuser unit: If the problem persists after trying the above steps, it is possible that there is an issue with the fuser unit. If this is the case, it may be necessary to have the fuser unit replaced by a professional.
If you have tried these troubleshooting steps and the problem persists, it is recommended to have the printer serviced by a professional. A technician will be able to diagnose the problem and determine the necessary repairs.
I hope this information is helpful. If you have any further questions or need additional assistance, please don't hesitate to ask.
HOW DO I CORRECT ERROR CODE C390 ON MY TOSHIBA ESTUDIO 3055C?"
Description:
Auto-toner sensor-C abnormality (upper limit)
Causes:
Auto toner sensor Harness LGC board Developer material
Remedy:
1 Developer unit • Check if the developer unit is installed properly. • Check that the developer unit and coupling on the equipment side are properly engaged. • Check that the mixer of the developer unit is rotated. • Check if the developer material is too dark visually. • Check if the amount of the developer material is too large or too small. • Remove any toner or dust on the ATC sensor connector and the drawer connector of the process cover. • Remove any toner or dust on the EPU sensor connector and the drawer connector on the equipment side. 2 Auto toner sensor Harness LGC board • Check the connectors and harnesses between the auto toner sensor and LGC board (CN365). • Check if there is any foreign matter such as toner in the connector of the auto toner sensor. Remove if there is and reconnect it.
How to fix toshiba photo copy machine not printing black and white but printing color and the black toner is full
If your Toshiba photocopier is not printing in black and white but is printing in color, there are a few possible causes and solutions to try. Here are a few things you can try:
- Make sure the machine is set to print in black and white. Some photocopiers have a setting that allows you to choose between color and black and white printing. Check the settings on your machine to make sure it is set to print in black and white.
- Check the toner cartridges. If the black toner cartridge is full but the machine is still not printing in black and white, there may be a problem with the cartridge. Try removing the cartridge and shaking it gently to redistribute the toner inside. Then, clean the contacts on the cartridge and the machine to ensure they are making good contact.
- Check the fuser unit. The fuser unit is responsible for heating and fusing the toner onto the paper. If the fuser unit is not working properly, it can cause the machine to not print in black and white. Check the fuser unit for any damage or debris, and clean it if necessary.
- Check for any error messages. If your machine is displaying any error messages, try to troubleshoot the problem based on the specific error message. You may be able to find the meaning of the error message and a solution in the user manual for your machine.
- If none of these solutions work, you may need to contact Toshiba for technical support or service. They may be able to help you diagnose and fix the problem with your machine.
Toshiba e studio 167 cannot use this size error how to fix it
Hi,
please power cycle your device and attempt to move forward. If error still persists, please alter the size of your paper to one that's appropriate for the printer or change the settings of the printer to allow for the paper size.
This would require you to reference the table of contents in the printer manual to follow the paper-size setup steps.
Thank you.
Toshiba 255 photocopier is powering off while running?
Hi,
Please double check that the printer isn't overheating because this might be a safety function activating due to high temperature. If this is the case, please lower the temperature from the a/c control in the room.
Also, please swap power outlets to rule out the first socket that you're using.
Thank you.
Not finding what you are looking for?