Sanyo DS24205 24" TV - Answered Questions & Fixed issues

This TV has the following inputs: RF input, composite video/audio input The easiest would be to use coax cable

You should have a remote control to change channels. If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one. To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability? Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have. Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the site http://electrohelponline.blogspot.com/ Check this site too. http://remotesearch.blogspot.com/ Universal remote controls are available at most of the electronic spare part selling shops.

If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy. http://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given.

Locate the manual for your television. Though slightly embarrassing, accidentally turning on the child lock to a TV is a common problem. The section In the manual about how to set the child lock feature will also explain how to unlock it. Try a few "universal methods" for unlocking the child lock. Some televisions have a universal code built in for disabling the child lock --no matter what your code is. A common code is "0000." Unplug your television for a few minutes. The internal battery of the TV is what helps remember what your code. If the TV is unplugged for an extended period of time, it clears the internal memory, which in turn will reset your child lock code.If you wish to get more details, check the site linked below. Pull up older posts there. Check the site with patience, as it has over 2400 posts now. All are related to electronic equipment repair help. If you search the site in Timeslide option, which can be selected from the drop down list at the top left of the display window, it will be easy to locate the related post. You can also do a search by type in the brand name to your device into its search box at the top right of display window.http://electronicshelponline.blogspot.com/

Hi,
i am imran
and i have also buy sanyo tv kit 360 ch fit in my old bpl 20"tv and i know for unlock tv channel.
try this this code definetly is solve your problem.
1st go to the locked channel.
and then press menu>system>child lock
and then press and hold down tv/av key and press swap key.
and see locked channel is unlock.
i have coming soon post for service code menu in short coming days.
please reply me to [email protected]

I HAVE A SNYO KIT ( 360 CHANNEL ) USING MICROPROCESOR IC LC863532C-58E2 I WANT TO KNOW THE CODES OF SERVICE MENU & HOW TO UNLOCK TV CHANNEL

You're in need for a universal remote setup code for this TV, I assumes and posts this solution. The setup codes for Sanyo brand TVs are given below. If you want more details about the setup proceedings, and more codes, check this link.0049 0097 0110 0004 0268 0012 0108 0180

On most , it is caused by Vertical IC and sorrounding components Guide on How to find Vertical IC Look and check for cold solder joints for IC501 part number LA7840Resolder the pins of the IC , and replace if necessaryLet us know if you need further assistance.

Visit this site 'Electro-help' for details. Service mode entering method to different brands, and adjustment proceedigns are described in detail there. Type in "electronicshelponline" into the search box of your browser, and search. It is a 'blogspot' site in English language. Pull up older posts there.

This is not a do at home repair and it will likely cost more than cost of a new TV to have a repair shop fix it.

Set has a bad vertical sweep IC. Also This Sanyo has a tendancy , when the IC blows out , to take the fusable resistor in the sweeo supply that feeds the vertical IC. This set should only be serviced by a trained technician because of ther high Voltage that lingers within. This repair should run you antwhere from 85.00 to 150 bucks. Good Luck

Hello
The vertcial output section in your TV is faulty. It may be either to a voltage loss to that section or an IC failure. Normally IC in this section will fail in most of the tVs. Vetical output IC can be located on the main board of your TV, normally screwed on to a metal heatsink to radiate heat from it while working. Locate this IC, and resolder all of its solder terminals by applying a little more solder, wthout making any solder bridge short in between adjecent solder terminals. If ther is any loose soldering, it will be cleared out. If this does not helps you measure the voltage that comes to that IC. If this is also found normal replace the IC. OK.

There's probably a bad Horizontal Output Transistor, (HOT.) It's close to the flyback mounted on a heat sink. You can test it with the diode scale on a multimeter with the TV off. Or you have a bad picture tube. This is usually a 135-195 dollar fix.

you might be able to scroll through the menus with the front panel buttons

but if not get a replacement remote from manufacturer

http://www.retrevo.com/support/Sanyo-DS24205-TVs-manual/id/311ci858/t/2/

If the tv has audio and video inputs why not use these instead of the coax input.That is,as long as you have an external tunerwith audio and video outputs.

must bring it to the service center

Hi,

Your tube Shadow Mask may have got magnetised and need to be degaussed. Some newer TVs will have a "degauss" function in the menu. This is most likely being caused by components. Do you have anything sitting directly on or next to your TV, such as VCR, Cable Box, DVR or stereo speakers? If this just happened recently you may not have damaged the picture yet. And if you move the components it may clear up otherwise you will have to purchase or make a degausser. You TV may have a degauss button. This will eliminate or minimize magnetic fields in the screen and should remove the de-coloration.

Also try turning off your TV at the mains and unplug it for at least two three hours, your TV should degauss the tube at power up. If this doesn't work you need to take it to the shop to get it diagnosed.Please get back to us if you have any further query or else accept the solution.

Thanks for contacting fixya.com

Normally all sanyo kits have two remote acces codes. One is Press Sleep Button on the remote handet and Menu button on the front panel of the TV simoultaneously.
Second is a tricky one.
Press Volume+/Vol_ to set the volume level to zero and press 'REP' on the remote control hanset aln loosen.
Keep pressing Vol+/Vol_ on the unit and press 'REP' on the remote control again.
Factory status will be displayed.
This is the service mode. You can adjust the parameters with the help of programe and volume control buttons.
To exit from the service mode, do the above said three again, unless the chaged parameters will not be stored in memory.
Another method is, if the hanset has a hidden key, usually at the lower side, which seems as a small hole. press it with a small stick to fit, may enter to remote code options.

does the TV respond on its built in control buttons?If built in buttons are working then the problem is the remote itself.open the remote control and release any stuck up buttons.good luck hope this helps!
Let me hear if you need further assistance...