20 Most Recent Sony FD Trinitron WEGA KD-36FS130 36" TV - Page 4 Questions & Answers

your best bet if you dont have a warranty on the tv is to get it repaired shouldnt be more then 150.00 you dont want the risk of having to fix something else if you get into the tv.

1)solder jungle IC,3.58 crystal and surrounding area. 2)Alternately,use heat gun then cool freeze to isolate thermal breakdown.

With electronics sources or monitors,asking a language preference is a first or early step in initial programming.To analyze the source of the "which language " request--dis-connect the cable box temporarily and hook up signal direct to tv.If ? is still there,the tv is asking it. If ? is gone,then the source box was asking. Any further assistance needed,please let me know.

If you are connecting the dish receiver to the standard antenna jack (F connector) on the TV, then the TV must be in TV mode and tuned to channel 3. If you accidently change to another channel then you will get the "no signal" message. If this is the case then simply put the TV back on channel 3. If you are using the RCA jacks (red, white yellow) to connect the dish receiver to the TV, then the TV must be in the VIDEO mode to work properly. If you accidently put the TV in the TV mode, you will get the "no signal" message. If this is the case then simply press the TV/VIDEO button.

Hello, please replace IC355. Best regards, Arpi

The light that you see flashing is the timer light. It is flashing because of the lack of red, green or blue. This would explain your color issue. It could e caused by the CRT (picture tube) itself or a bad connection to the CRT or a color driver component failing. Either way you need a technician to locate the issue. If its the CRT and it is out of warranty, most likely it won't be worth the repair.

check if the main fuse blew up. good luck!

If you want to test the voltage you can do so at connector CN002 on the main board. You should have 5 volts DC at pin 4 and at pin 5 marked SIRCS (sony infared remote control system)should be 5 volts as well but, will drop to about 2.5 volts when any button is pressed on the remote. If it doesn't change then you should change the HR board wich houses the IR rec. and associated components.

The horizontal size adjustment is in the service menu only. I would suggest someone who knows the code to do it for you.

The sequence of flashes from the timer light may hold the clue as to what is wrong. For instance if it blinks 5 times then 3 before repeating the cycle, it usually means that IC 702 on the CRT drive board is bad. I have had to replace that semiconductor many times in the past. For this exact symptom, removing the connector Cn706 From the CRT Drive Board allows the set to start up. I am very skeptical of the quality of picture tubes in these sets, so if this is the problem, it may occur again. When replacing this IC, there could be damage to a resistor and capacitor R533 and C541 on the main Printed Circuit Board also. If your timer light is not flashing that code, the problem is elsewhere. If the set is over 6 years old, it may be worthwhile replacing it.

the symptom is usually caused by a breakdown in the power supply circuit. in most modern receivers (transistorized and/or ic), it may also be caused by a breakdown in the horizontal deflection circuits (hor. oscillator, pre-drive, or drive circuits). supply voltages for the tuner, vif,sif, and vertical output are usually supplied by the horizontal output circuit. but if you doesnt know anything about these stuffs, better bring it to a qualified service technician

Sorry to say, it sounds like a bad picture tube, But could be also the capacitor that filters the screen voltage on the crt drivers. In all my years though, your complaint has been the picture tube. Good Luck.

Question edited for clarity, proper name, fix typo. Manual and Reviews

Manuals for HT-CT260

Sony https://www.sony.ca > electronics > support > product Find instruction manuals and brochures for HT-CT260.

Sony HT-CT260 review: Excellent sound that fits nearly ...

CNET https://www.cnet.com > reviews > sony-ht-ct260-review May 7, 2013 - The Sony HT-CT260 is our go-to budget sound bar pick, with excellent sound quality, built-in Bluetooth, an adaptable design, and no major ... Rating: 8.4/10

Sony HT-CT260 Home Theater Soundbar Review

PCMag https://www.pcmag.com > Reviews > Audio > Speakers Feb 28, 2013 - The Sony HT-CT260 soundbar adds Bluetooth to an already highly capable and modestly-priced two-piece audio system. MSRP $299.99. Pros and cons: Excellent value ? Built-in Bluetooth ? Treble response isn't the clearest ? View full list Rating: 4 · ‎ Review by Will Greenwald · ‎ US$225.00 · ‎ Out of stock ..

Pano po ireset ang cybertec 8 in 1? Salamat po

All questions need 'make model (what is is)' as first 3 words in every question please. Television? Stereo? Sound bar? ICE? The grinding noise makes me think you have a cooling fan issue, in which case the flashing LED would be signaling an overheat situation. You can Google sony model blink codes ..

Good set and worth getting it repaired. https://www.google.com/search?q=Sony+KDL+46v51000+parts& https://www.fixya.com/support/r29790007-repairing_own_television ..

ChatGPT 3.5

User
I need code for newstar ntr b28z for my Sony tv

ChatGPT
Unfortunately, I can't provide specific code for your Sony TV remote without knowing the exact model number. However, you can usually find the code in the user manual of your Sony TV or by contacting Sony customer support. Alternatively, you can try using the auto-search feature on your newstar ntr b28z remote to find the correct code for your Sony TV.



User
need code for newstar ntr b28z

ChatGPT
To find the code for your Sony TV using the Newstar NTR B28Z remote, you can try these general steps:

Turn on your Sony TV.
Press and hold the "TV" button on your Newstar remote until it blinks twice.
Enter the code for Sony TVs. Some common Sony TV codes are: 0000, 0011, 0080, 0111, 1234. If none of these work, you can proceed to the next step.
Press the "Power" button on the Newstar remote. If the TV turns off, the code is correct. If not, try a different code.
Once you've found the correct code, press the "TV" button again to lock it in.
If none of the provided codes work, you might need to consult the manual of your Newstar remote or contact their customer support for assistance.

str no

2 red light blinks can mean a power supply problem that can be caused by a problem on the main board. An authorised Sony repair shop can fix that for you.