20 Most Recent D-Link 802.11g Wireless Router WBR-1310 (WBR1310) - Page 8 Questions & Answers

The 802.11g supports up to 254 connections, however, the bandwidth is shared amongst all the connections. So, theoretically, you'd have only about 200K speed if all 254 connections were being used (actually less). To limit the number of connections that can be made simultaneously, change the number of clients in DHCP (limit the range of IP addresses it assigns).

First i need to know more of your network infrastructure to help NAT (Network Adress Translater) problems can depend on lots of things

it could be a QOS (Quality Of Service) setting in the router, it could be RF noise generating from the XBOX causing loss of wireless performance, it could be a firewall ruel in the router, it could be some bad DNS settings

try connecting the XBOX with a wired connection, if all is OK then concentrate on the wireless part of the router

Press the reset hole on the back of the router in with a pen for at least 30 seconds. This will reset your router to factory settings

Most routers don't require discs and the disc usually contains mere documentation for configuration and help. Routers are usually plug-and-play type devices but if you're definitely wanting some type of program or information. You can visit the below link for your router.

http://www.dlink.com/products/support.asp?pid=474&sec=0#applications

You'll need to specify by clicking the "Click Here" based on the revision of your router (A, B, or D). Once you've selected a revision, you'll be able to download the application and firmware updates for your router.

check whether it wants security key.ask service provider for default key. or signal strenght might be low.

A way to get around this issue is to do a static ip address for the other devices in your home. You'd have to connect to the router and set it up, i believe its by MAC address and you assign the IP.

-mk3ride

Yoy may want to look into changing the channel that it is broad casting on. Most routers have 1-11 channels that you can select to avoid others that are broadcasting on the same channels. Also Wireless telephones, microwave ovens, etc. operate at near thye frequencies of some of the channels and may interfer, thus causing dropped signals. Go into your set up and select a channel other than the default 11, maybe? or another until you correct the problem.

Your modem most likely needs to be powered-off for about 15 minutes in order for the NVRAM to clear the MAC address of the device that you previously had connected to it.
Unplug the power cord from the modem and wait about 15 minutes with the power off. After the 15 minutes, connect the router to the modem with the Ethernet cable and plug the power cord of the back in to the modem. One the modem has completed its startup, it should then work with your router.
If this does not work, then you may need to call your ISP to have them remotely clear the old MAC address from the modem so that it will work with your router.

in back side of router you will find small hole for reset, please push that button for 15 second during power on then try to restart router.it will reset to default password.

The WEP encryption key is in your router's wireless settings. Log into your router and got to the wireless settings, you will need to get the SSID and the WEP key. Then go to your computer/laptop's wireless card and configure it with the router's SSID and WEP key, so it will then connect to the wireless router and the Internet.

To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security.

To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1).

Enter the user name (admin) and your password. Leave

the password blank by default.

If you get a Page Cannot be Displayed error, please

refer to the Troubleshooting section for assistance.

The manual:

http://www.scribd.com/doc/4040609/wbr1310-manual-110

Click on this link or copy and paste the complete link into your browser.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!

Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Go to D-Link - TechSupport FAQ.

If you need more help come back.

Post / thumbs / testimonial are welcome!

yes you can, you need to manually configure settings

Go to Dlink website and download the latest drivers/ firmware for your router. That may fixs the problem

give the this ip to your pc 192.168.0.100 when connect with dlink adaptor with lan cable and sub netmask 255.255.255. (manul ip for connecting)

Just reset it! At the back of the router is a small hole.With a toothpick or some like press gently for 30 seconds and wait for the router to start up again.Log in to http://192.xxx.xxx and start a new configuration.

If you need more help come back.Post / thumbs / testimonial are welcome!

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Click on wireless then wireless security Enable WEP then enter new password save settings and restart router .Then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa

1st you need to configure the the D-Links wireless settings eg, the SSID and encryption, and the configure the wireless card in the computer/laptop with the D-Link's wireless settings so it can connect to the D-Link.
To secure you wireless network from unauthorized access, please click on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security

Hello;
First connect via Ethernet. Then

• Click START'RUN and then type CMD
• At the black window with the prompt(cursor) type ipconfig and search "default gateway"
• Type the gateway address in the browser ej: 192.168.0.1

This is for enter the web administration of the router. I don't know your revision. But I will get you the Hardware Version: A1 Firmware Version: 1.04

• Aim for Status as the picture above

On the WAN section is the actual Internet. WAN = Wide Area Network. Your computer is actually on the LAN = Local Area Network. The Computer looks the address on the router, then the router go to the WAN for the information. But this is transparent to the user. If the WAN is in cero on the addresses, you have to check the installation. when the installation are correct power cycle the modem and the router and try again. Always connected via Ethernet cable. Hope to help!

You don,t need to reset your router password only if you can,t log in the router configuration page.

If you need more help come back.Post / thumbs / testimonial are welcome!