Sylvania 6842PF 42 in. EDTV-Ready Plasma Television - Answered Questions & Fixed issues

An HDMI to RCA component or composite cable only works for video projectors that are designed to read a computer signal. TVs, Blu-ray players, and DVD players use a different format compared to computers. You need an HDMI to RCA converter. An example is available here: http://www.bhphotovideo.com/c/product/770115-REG/KanexPro_HDRGBRL_HDMI_to_Component_Converter.html . I hope this helps. Cindy Wells

The provider should at least give instructions or connect it up for you---lots of ways to do this if using a receiver and a sat box etc.Start with looking over the owner manuals for what you have. A lot of TV shops will for a fee come out and hook everything up right.

Four digit set up codes for GE TVs are: 0031 0107 0164 0004 0009 0044 0054 0000 0342 0003 0125 0015 0022 0052 0087

Hi I would guess that there is a problem with one of your sustain boards. also your logic board might be bad.You can get parts at www.interliquidparts.com

Hi,

The correct setup depends on whether you have a cable/satellite receiver and whether you want to record to and playback from the VCR. If you are using a cable/satellite receiver, this needs to be connected to both the TV and the DVD/VCR if you want to record. The DVD then needs to be connected to the TV via the video and audio out sockets on the back of the DVD/VCR for playback.

I can let you know exactly which connections to use and where they should all go, but I need to know the following details as otherwise I don't know which sockets/connect you have available.

1. Brand and model number of TV
2. Brand and model number of DVD/VCR
3. Brand and model number of any cable/satellite receiver if you are using one.

Please confirm these details and I will try to assist you further.

Regards,
BElectric

You have to make sure the tv/vcr switch is on, the way you do this is put a tape in and press play, make sure the set is set to 3 or 4 in back of VCR, then make sure your tv is program to that channel 3 or 4 it has to be programmed and to be prog,, it must see something there.

You just can't. Not without an external receiver.

Your TV is simply missing a piece of hardware - it is called TUNER - that can understand the signal that runs through the cable (or an antenna) and decode it into simple video signal.

So the only solution is to buy an EXTERNAL TUNER device (also called external receiver or external set top TV box).

Those are rather cheap compared with what they used to be, but if you care for an advice from professional it is: sell your TV and use the revenue towards the purchase of a new one. All TVs currently in the mainstream sales channels have that thing built-in.

Some of the older models that you will find on Craigslist (like yours) do not.

it is usually not a problem for users with cable TV because most cable TV boxes also have a built-in tuner. If you are talking about how to connect your TV to your local cable company then the right thing to do is call your cable operator and tell them you want a newer receiver that outputs standard composite (one yellow one red one white) or component (green, blue, yellow and white and red) - if your TV has the later.

Hope this helps. If it does please rate accordingly.

Cheers,
www.coppelltvrepair.com

You can either get a svideo to coax switch box or get a old vcr and run your cable through it.

there should be a dvi or vga input on the tv you will need a male to male vga lead and plug it in to tv and graphics card and switch it on

this is a monitor plasma tv and it will need some type of tuner to bring the cable channels down to the audio/video jacks or the composite video jacks(blue/red/green) you can use a cable ready vcr to input the video in tv jacks and hook up the cable in to your vcr rf input.

if stand-by voltages are good, you probably have bad inverter board. could be one or two depending on unit

These sets are manufactured by Funai, in my opinion total junk, yet they command a $1,500 price tag. I cannot find parts available for this hunk of **** anywhere so if this tip helps you fix this set and get it out of your hair, God Bless You! Model number is followed by an M to read: 6842PF M Found no VSUS on connector CN2502 of the SMPS. VSUS was shorted to adjacent GND pin by 120 Ohms. Small high voltage blue capacitor C2250 (Between Two very big electrolytics and right next VSUS diode D2250 (TO-220 package) on aluminum heatsink) shorted, burned. I have two of these sets in the shop at the same time, both of them have the very same problem, appears to be common and parts seem to be NLA for this unit. Replace C2250, 1,500 pF @ 1Kv. Usually marked as 152K on small high voltage capacitors in junk units. This is not a common value part so if you have to, make one by parallelling a .001 uF cap (102) with a 470 pF cap (471) to get a suitable 1,470 pF capacitor at 1 Kv. Adjust VSUS with VR2250 on SMPS board to read 175 VDC to GND and you are done. You're welcome. ~Ohmster

DVDs are 480p
HD-DVD or Blu-Ray DVD is 720p or 1080i or 1080p

you cannot increase resolution, if you want to play a 480p/i video on a 1080p/i or 720p screen, you are merely stretching the picture.

If there is any kind of box that tells you it can convert 480i/p to 1080p/i or 720p(high definition) it is simply stretching the picture.

you can convert 1080p/i or 720p(high definition) to 480i/p as you are taking out information from the video to make it smaller.

Guess what you may have hit the nail on the head. Plasma TV used a balast type power system for the backlighting and that is what you are hearing. I would suggest getting this set looked at to see if the plasma excitor needs to be replaced (it may have another name in this brand of set).

This sounds like the color processor IC is not working properly. If this is the case you will have to have this checked by a qualified technician.

listen what you do is go down your local electronics shop and buy a video card or scart card which allows yyou to connect your pc to your television and v v . and the surround system wer you connect your pc speakers you buy a lead whiocih allows your to convert a phono plug to a 9mm phone jack and use that. hope it helps you.

No, because screen casting wasn't invented and it isn't a Smart television. Time for a new one.

Here are some troubleshooting tips to try. However, as it is an older set, if these tips fail, the cost of a repair at a shop might exceed the value of the TV. In short, a new TV may be in the works. Cross your fingers. One of these tips may work. Let's troubleshoot the issue and try to get it working: If you are using a remote, check the batteries in it. If you are using several remotes with it, try the alternative remote. Sometimes there is a glitch affecting the remote for a Roku where it won't turn on the TV other than a powered black screen and you have to use the other remote to turn it off and back on and then the Roku screen pops up. I have not sorted out why. Check Power Cord and Connections: First, ensure that the power cord is securely plugged into both the TV and the electrical outlet. If you suspect a faulty power cord, consider trying a different one. Reset the TV: While most Sylvania TVs don't have a dedicated reset button, you can perform a manual reset: Unplug the TV's AC adapter from the electrical socket. Press and hold the Power button on the TV for 20 seconds. Plug the AC adapter back in and turn on the TV. Check Audio/Video Cables: Inspect the audio/video cables connecting your TV to the satellite or cable receiver. Ensure that the color-coded prongs match their respective connecting points. Correct any mismatches (e.g., white cable into a red port) by reorganizing the prongs. Inspect Coaxial Cable: Look for the coaxial cable on the rear side of the receiver, attached to the port labeled as ANT IN. Confirm that the connection is firm; a loose coaxial connection can cause display issues. Tighten the cable by pinching the silver band on the end and rotating it clockwise until secure. Check for Interference: If distortion continues on the TV screen, consider nearby interference. Power-hungry appliances can cause electronic interference, affecting display quality. Visit a Repair Shop: If the above steps don't resolve the issue, you may need professional help. Some technical faults, such as a blown fuse or faulty capacitor, require expertise in dismantling and soldering. If uncomfortable with such tasks, consider visiting a repair shop

1. Auto Code Search:
   • Turn on your Sylvania TV.
   • Press and hold the "Code Search" button on your Philips remote until the indicator light stays on.
   • Press the "TV" button on the remote to set it to control the TV.
   • Press the "Power" button repeatedly until the TV turns off.
   • Press the "OK" or "Enter" button to save the code.
2. Manual Code Entry:
   • Find the code for your Sylvania TV in the Philips remote control manual. If you don't have the manual, you may be able to find it on the Philips website.
   • Turn on your Sylvania TV.
   • Press and hold the "Code Search" button on the remote until the indicator light stays on.
   • Enter the code using the number buttons on the remote.
   • Test if the remote now controls your TV. If not, repeat the process with a different code.
3. Try Common Codes:
   • Some common Sylvania TV remote codes for Philips remotes are 0810, 1684, 1886, 2183, 1081, 1172, 1196, and 2049. Try entering these codes manually.

it is a very simple TV, is TV connected to cable? Here is link to manual copy and past download and save for future reference. It is very old and has CRT not LCD. https://www.manualslib.com/manual/776815/Sylvania-Sylvania-Ssc092.html#manual