Jura Capresso Impressa E9 Espresso Machine & Coffee Maker - Page 2 - Answered Questions & Fixed issues

Take out the used grounds container, and put the drawer back in the machine. After the machine has finished positioning, then you can put the container back in the machine.

I had a similar problem, and solved it by turning the grinder by hand against resistance. Apparently the grinder wasn't really turning during the cycle and needed to be cleared. If your beans are "hopping" this may be a different problem.

Everytime the mainswitch is turned off you must set the time, there`s no backup battery on the machine, so the time is lost everytime you power down. If you set the time you can program on/off time. To avoid this every day, just use the standbymode.

Disassembly of the grinder is most likely due. There are springs and ball bearings in there so be careful not to lose any parts. I learned that the hard way. I can send a pictorial, written in German, but helpful. e-mail me at [email protected].
Mike

Hi,

What kind of machine do you have?

Hi there,
check out this link:
http://capresso.com/pdf/inst_e_series.pdf

Ah the Subaru Impressa with S9 engine. :>D Not quite "says it all" Bryan. So..... Question edited to add the maker and 'what it is', a Coffee Maker. Question moved from Cars and Trucks to Jura Impressa category. When you add a maker, you are offered the correct category, 'Impressa' gives you generic Cars and Trucks. You have a 'Replace Now' message that no one else has! https://www.google.com/search?q=Jura+Impressa+S9+%22replace+now%22 However, try this. Remove the Grounds Bin. Disconnect from the power. Replace the bin, reconnect power. This is your manual https://www.seattlecoffeegear.com/assets/user-manuals/jura/jura-impressa-c9-user-manual.pdf Press CTRL+F, and type 'replace' and press enter. There are 16 mentions. I think it refers to the grounds bin being not fully placed. I have come across this many times, there is a small infra-red sensor or a proximity sensor.

Two to three teaspoonful water overflow after each espresso is normal. That is why the tray is there. If water collection in the tray is excessive and programmed espresso is smaller, then there is cause for worry. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

Error 5 is pointing to heating problem. Here are the parts that may be malfunctioning: 1- Thermal sensor not registering heating. Replace it. 2- Heater not heating up. Check continuity on heating element. If there is no continuity, (This is rare). Replace heater (Thermo block). The problem can be linked to: 1- Missed descaling of machine for extended period. 2- Use of automatic descaling method suggested by Jura. Descale the machine every three months using Manual descaling method.. Services Unlimited Inc Parts Guru Since 1988 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

Fortunately the problem you describe is not model specific. All Jura machines in the series C, E, F, J, S & Z models have the same problem. The Jura recommended maintenance is insufficient or erroneous. Here is how it occurs: 1- When new machine is set up, the instructions advice the owner to set up OK for use of Filter cartridges. This set helps only to display reminders for replacing the filter. 2- The initial set up instruction also advises that with regular use of Filter, descaling the machine will not be needed. That is really not accurate. Consequently, the reminders for descaling are delayed for over one year or more. This causes serious consequence with accumulation of Calcium deposits in the entire hydraulic and coffee system. 3- Use of Filters alone does not prevent Calcium deposits. Cleaning tables recommended & sold by Jura do not remove Calcium deposits in the coffee/water passages. The automatic descaling method recommended by Jura leaves the coffee side of the machine unclean. The error message in your machine is due to Calcium deposits in the Brew group, coffee outlet & the faucet dispensing coffee in the cup. I suggest all Jura machine owners should manually descale machine. Manually descaling includes use of 6 to 10 rinse cycles with descaling solution in the water tank. The error message "Clean Machine" is accurate. This error message is pointing to descale the Brew group, coffee outlet tube and coffee dispensing faucet by using rinse cycles.

After the rinse cycles are complete, refill Descaling solution in the water tank & continue descaling the rest of the machine by using hot water dispensing function, ½ cup at a time until the tank is empty. Finally, give a final flushing of machine to flush out remaining descaling solution inside the machine. Services Unlimited Inc Parts Guru Since 1988 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

Hi Shoba Photo sensor or switch is blocked. Not sure if yours is an Infra Red beam or switch Clean & inspect with flashlight Look for light path (blocked) or moveable part (switch) Actually.... it must use an Infrared Light Emmiter to shine through the grounds holder to the sensor on the other side/ 10 Minute Fix.... I hope

Plug it in.............................

Fill the water tank with vinegar to dissolve the chalk and make the swimmer swim again. It is stuck! You can help and poke the swimmer with a knife from the side.

Too Much water , use less water .

How to access grinder itself? Where is it? My Jura C5 doesn't grind coffee beans at all. Firstly grinder has started with starnge noise and then stopped with alarm "no beans", now it doesn't start at all..

Unfortunately, without being there in person to inspect the machine and its components, it's difficult for me to provide a definitive answer. However, I can offer some general guidance that may help:

1. Consult the user manual: The user manual for your Capresso C3000 should have a diagram or schematic showing the different components and their connections. If you still have the manual, check to see if there's a helpful diagram inside.
2. Look for visual cues: While it can be difficult to identify the tubes by sight alone, there may be visual cues that can help you narrow down which tubes go where. For example, one tube may be thicker or more flexible than the others, or it may have a different color or texture.
3. Experiment with different configurations: If you're unable to find a diagram or visual cues, you may need to experiment with different configurations until you find the correct one. This can be time-consuming and frustrating, but it may be the only option if you're unable to find any other information.
4. Seek professional help: If you're still unable to identify the correct tube configuration, you may want to consider seeking professional help. A qualified technician or repair service may be able to identify the correct configuration and get your machine back up and running.

I hope this helps, and I wish you the best of luck in getting your Capresso C3000 back in working order!

http://www.fixya.com/support/t12615678-capresso_303_will_not_steam

Talk him

The first thing to check is the seating of your water tank. Just a few grains of coffee grounds or dirt underneath the tank are enough to break the watertight seal. Make sure the area under the tank is absolutely clean. That's always worked for me when I've had the leaking problem.

Rinsing cycle at start up is electronically programmed function. Unplugging is a temporary solution. Jura will not sell parts or offer any guidance. I could look into more details to find an answer but the model Capressa 50 is not listed in my Data base. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a