Top 20 Sony DVP-NC85H Multi-disc DVD Player - Page 5 Questions & Answers

Hi You can try. Part 1: Manual Factory Data Reset with TV buttons Press and hold the Power button and Volume Down (-) buttons on the TV (not the remote), and while holding the buttons, plug the power cord back in. Continue to hold the buttons down until a green LED light appears near the Sony logo on the TV front. ----------------- How do I factory reset my Sony Bravia TV manually?"); display: inline-block; height: 24px; width: 24px; margin-top: -1px; transform: rotateZ(-180deg);"> Factory data reset

1. Press the HOME button, then select [Settings] - [Device Preferences] - [Reset] - [Factory data reset].
2. Select [Erase everything]. If you have set a PIN code on your TV, you will be prompted to input it when you select [Erase everything].

kindly check the power board if all voltages are there

The 6-time blink code for the Sony KE-42TS2U indicates a backlight error. This may be due to a faulty backlight inverter board, or a problem with the power supply to the backlight inverter board. It is recommended to have the TV serviced by a qualified technician to diagnose and repair the issue.

perform a soft reset. Turn off the TV, unplug the connector from the socket, and wait 2 minutes. ...

If your Sony VPL-CS5 Red LCD isn't working, you may need to replace the lamp. You can purchase a replacement lamp from the manufacturer's website or from an authorized retailer. You may also need to check the power cord and connections to ensure that everything is properly connected. If the issue persists, you may need to contact Sony customer service for further assistance.

Hi, please run a channel scan on your tv before checking for the issue again. If the issue persists, please remove all accessories from the tv before restarting it. If necessary, you can then power cycle the tv. Otherwise, you can move onto running a factory reset on your Sony tv. Thank you.

The power supply is not working or there is a power black out or a fuse is bad or the wiring is either loose or no longer working.Or the receiver is bad.

I'm sorry to hear that you are having issues with your Sony Bravia TV. It sounds like you have already tried a number of troubleshooting steps, including replacing the boards and performing a software update. If you have no picture on the TV and the Sony logo is flashing on the screen before going off, it could be an issue with the software on the TV. Here are a few additional troubleshooting steps you can try:

1. Disconnect the power cord from the back of the TV, then unplug the TV from the wall outlet. Leave it unplugged for at least 60 seconds, then plug it back in and try turning it on again.
2. Check the HDMI connections on the back of the TV to make sure they are secure.
3. If you are using an HDMI cable to connect the TV to a device (such as a cable box or DVD player), try using a different HDMI cable.
4. If you are using a cable box or satellite receiver, try resetting it by unplugging it from the power outlet for 60 seconds and then plugging it back in.
5. If the TV is still not turning on or the picture is not coming back, it could be an issue with the software on the TV. In this case, you may need to try a factory reset. To perform a factory reset, follow these steps:

• Press the Home button on the remote.
• Select Settings.
• Select Product Support.
• Select Customer Support.
• Select Factory Reset.
• Follow the on-screen instructions to complete the factory reset.

Keep in mind that a factory reset will delete all of the data and settings on the TV, so you will need to set it up again as if it were a new TV. I hope these steps help, and please don't hesitate to ask if you have any further questions.

The programming code for the Sony BDP S500 to be used with the RM-AAP013 remote is 31758. Here are the steps to program the remote:

1. Turn on your Sony BDP S500 player.
2. Press and hold the "S" button on the RM-AAP013 remote until the "Amp" button flashes.
3. Enter the programming code 31758 using the number keys on the remote.
4. Press the "Enter" button.
5. Wait for the "Amp" button to stop flashing.
6. Test the remote to ensure that it is working properly with the Sony BDP S500 player.

To program a Sony TV, you will need to follow these steps:

1. Press the "Menu" button on your remote control.
2. Use the arrow buttons to navigate to the "Settings" menu, and then press the "Enter" button.
3. Navigate to the "Installation" or "Setup" menu, and then press the "Enter" button.
4. Select "Programming" or "Channel Setup," and then press the "Enter" button.
5. Follow the on-screen instructions to scan for available channels. This will typically involve selecting your cable or antenna source and then initiating the scan.
6. Once the scan is complete, use the arrow buttons to navigate through the list of channels and select the ones you wish to keep. Press the "Enter" button to lock them in.
7. Exit the menu when you are finished.

Note that the specific steps may vary depending on the model and software version of your Sony TV. You may refer to the manual of the TV to get more information.

Hi, please check whether the sony remote code book includes vizio as a category. If not, then the two devices are not compatible and you'll need to call vizio to figure out which remotes are compatible with your tv and then choose from that list before programming the new remote to your tv. Thank you

If you're seeing a solarized picture on your Sony TV XBR-43X800G, there are a few things that could be causing the issue. Here's how to fix it. First, check the input source. If you're using an HDMI cable, try switching to a different input. If you're using a component cable, make sure it's securely connected to the TV. If the input source isn't the issue, try resetting the TV. To do this, unplug the TV from the power outlet and then plug it back in. Once the TV is back on, go to the Settings menu and select Picture. Scroll down to Picture Mode and select Standard. If you're still seeing a solarized picture, there may be an issue with the TV itself. In this case, you'll need to contact Sony customer support for assistance.

To get a ST-PTZMINI-540W camera to work with a Nuvico DV3 1600 remote, you will need to follow these steps:

1. Connect the camera to the remote using a RS485 cable.
2. Configure the camera's communication settings to match the remote's settings. This can typically be done through the camera's on-board menu or through the use of a software configuration tool.
3. Once the camera is configured to match the remote, you will need to set the camera's address to match the remote's address.
4. Once the camera and remote are configured, you should be able to control the camera with the remote.

It is important to refer to the user manual of the camera and the remote as the steps may vary depending on the model and firmware version. If you are not comfortable working with electronics or you are not sure about what you are doing, it is always best to consult with the manufacturer or a professional technician.

https://www.servicemanuals.net/en/sony-service-manuals

Possible TCon board issue but check Pico fuse on Power Supply. Fuse is located near top left closer to connector plug . Fuse is marked as L7. If faulty, replace ONLY with the correct value and type of fuse.

1. Check your TV's audio settings: If you're experiencing audio issues with your Sony TV, the first thing you should do is check the audio settings. Make sure that the TV is set to output audio to the correct source. For example, if you're using an HDMI cable to connect to a sound bar, make sure that the TV is set to output audio to the sound bar. If you're using a receiver, make sure that the TV is set to output audio to the receiver. 2. Try a different HDMI cable: If you're using an HDMI cable to connect your TV to a sound bar or receiver, try using a different HDMI cable. Sometimes, the cable can be the issue. 3. Check your sound bar's audio settings: If you're using a sound bar, make sure that the sound bar is set to the correct audio input. For example, if you're using an HDMI cable to connect the TV to the sound bar, make sure that the sound bar is set to the HDMI input. 4. Check your receiver's audio settings: If you're using a receiver, make sure that the receiver is set to the correct audio input. For example, if you're using an HDMI cable to connect the TV to the receiver, make sure that the receiver is set to the HDMI input. 5. Try a different audio input: If you're using an HDMI cable to connect your TV to a sound bar or receiver, try using a different audio input. For example, if you're using an HDMI cable to connect the TV to the sound bar, try connecting the TV to the receiver using an optical cable. 6. Restart your TV: If you're still experiencing audio issues, try restarting your TV. Sometimes, this can fix the issue.

The 7 blinks on your TV is letting you know then that there is an error with the temperature of your TV or the sensor is not working or your TV is overheating. Or there is is an issue with the KD board or the GD board or an audio error.

Likely to be the power board, but this is what often happens https://www.fixya.com/support/r29790007-repairing_own_television ..

Replace the main board if you can find one.