20 Most Recent Sunbeam 5891 Bread Maker - Page 9 Questions & Answers

then programme it on the bake cycle.

twist it then pull. try both anticlockwise and clockwise.

Generally, an HHH error code means the machine is sitll too hot from making the previous loaf. Keep the door open for a bit and allow it to cool down.

Either spay a non stick spray on the blade/paddle before you began or simplly remove the the blade/paddle after the kneading cycle is completed

If there is trip switch on the backside or underside please check. if not check the power to the switch and to the motor.
Since there is nothing more than this the fault can be a connection or the motor. make sure the switch is working.

Ask the breadmaker manual search engine:

manualfox.com/searchengine/breadmaker.htm

If they find it, they will provide you a direct download link.

Ask the breadmaker manual search engine:

manualfox.com/searchengine/breadmaker.htm

If they find it, they will provide you a direct download link.

You can get them wound in any windiing shop that specialising in imported machines.
Both the transformer and the motor must be REDONE for 230V instead of the 110 in which case you will require another step down transformer.-- additional cost.
Get an estimate and warranty on the job before you can get the winding done, or else I recomment not to proceed because unless the person who winds do not do it technically well for 230V, the motor or transforemer will not last.
Check this out and decide.

Hi. They sell the belts at Amazon for about $10.00. First you should make sure the paddle is not stuck. Take the bread pan out and see if you can turn the paddle by hand. Keep pan out of machine and start a kneading cycle. If motor shaft does not spin then it's probably the belt. Motor and belt is located in base of machine. Make sure you unplug the machine before checking out the belt. Hank

Hi,
You can not reseal the sealed bearing that is on the bottom of the bread pan. Bread pan needs replacement. Try Amazon. Hank

good day,
hope this link below will solve your problem.

try the modern baking:time saving techniques for bread.
by nick malgieri.

Hi, If it is not mixing well it could be three things. 1) Make sure the bread pan is inserted in the machine correctly. 2) The paddle is sticking. 3) The belt is loose. Take the pan out and see if you can turn the paddle freely by hand. If yes ok. If no, the sealed bearing that the shaft goes through is failing. If everything is ok then check the belt that turns the motor shaft. Motor and belt is located in the base of the machine. Be sure to unplug machine before checking the tension of the belt. Hank

Hello. Great news. Here is the owner manual for you

http://ec1.images-amazon.com/media/i3d/01/A/man-migrate/MANUAL000063299.pdf

J.

Hi,
The sealed bearing on the bottom of the bread pan is leaking and is defective. You should call Sunbeam and ask for a replacement. Good Luck Hank.

Hi....If under warranty call for service. If not, then check out eBay or Amazon. You will need model # of your machine. Keep in mind that a new machine sells for around $50.00. Don't spend too much on a replacement pan when you can get a new Sunbeam. Hank

Check the troubleshooting section in your manual. You will get any Sunbeam breadmaker manual with the manualfox search engine. Check results here:
http://manualfox.com/link/sunbeam.htm

Checked the manual but no info in http://www.sunbeam.com/Manuals/MANUALS/005891-000-000_43_4357793.PDF

Would suggest checking with your local Service Center, locatable via http://www.sunbeam.com/ServiceLocator.aspx?section=kitchen

Hi...No problem at all. Beats fishing the paddle out of the bread. Hank

go to the company where it was purchase they will help u out

Hi, No problem at all. People do this to prevent the paddle from staying in the bread. If bread machine does not have a pause, take the pan out of the machine to remove the paddle to be safe, and do this before final rise and baking cycles. Hank