Top 20 KitchenAid 30 in.KECD806 Electric Cooktop Questions & Answers

Hi,
I have checked a number of sites and many of the gaskets or seals for this model are not available....
I would call a site like this one and see if they could recommend a functional replacement for you.

http://www.appliancepartspros.com/partsearch/model.aspx?model_id=238863&diagram_id=28248973#d28248973

heatman101

Mis-wired or the new control panel is faulty. Call them back, it is under repair warranty. The parts aren't cheap! https://www.searspartsdirect.com/model/41v4g0ja62-000593/kitchenaid-kecc667bbl01-electric-cooktop-parts ..

igniter failed

Almost certainly the switch, not the element, Had the same problem on a different stove - went to 10 no matter what the knob was set to. Here is a parts list, you should be able to get the part from a local appliance part seller. I used ReliableParts in my town. https://www.partselect.com/ModelSections.aspx?ModelID=815598&ModelNum=KECD805HBL3&mfgModelNum=&ManufactureID=3&Selected=ZPGZLZRB&Position=2&mfg=Whirlpool&Type=Cooktop&Mark=2

How to Install Cooktop

They go under the counter and they are screwed in place

Hi, Need model number of your range to answer this question. Is this gas or electric? Is this a freestanding range or cooktop because I only can find information on ranges with this fault code given. All should EEPROM communication error which is a communication error on start up. when the top was damaged was the unit being used? Was water or liquid a factor when this damage happened? A loose wire would be a different error code or fault code like a F2 - E1 or E2, not your code given. I hope this helps, need more information. Thanks I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Call the repair company to come back. It's possible he didn't hook something up right. ...

To Unlock Cooktop: Touch and hold the CONTROL LOCK/ ALL OFF keypad for 5 seconds.

How I fix this problem! Thanks For Your time!

IF YOU DONT HEAR IT CLICKS, MOST LIKELY PROBLEM IS WITH SPARK MODULE, IF YOU HEAR IT DOES CLICK, BUT GAS DOES NOT IGNITE, CHECK IF IGNITERS FOR CRACKS OF CERAMIC INSULATION, THEN ITS BAD IGNITER. IN SOME CASES IT MIGHT BE A SPARK SWITCH. JUST TAKE A LOOK AT THIS VIDEO, IT WILL GIVE YOU AN IDEA HOW THEY MADE, AND WHAT MIGHT BE WRONG. HOPE IT HELPS.

Get yourself a $5 electric socket tester at a place like Lowes or Home Depot and check all of your electric plugs it will tell you if all three wires in the socket are correct, wire wrong or if one is open,

Everything about It.. Thanks for watching

changing everything on this kitchenaid cooktop video

You are either: A) missing the mounting screws and brackets that hold the unit in place B) it is stuck and will require brute force to remove C) both

Is there directional grain..? I have removed small imperfection in stainless look by gengtly rubbing only in the same direction as the existing grain.. and be careful sometimes the repair is worse than the issue..

2 POSSIBLE PROBLEMS 1ST (AND MOST LIKELY) - SPARK MODULE IS BAD, 2ND - SPARK SWITCHES; CHECK MY VIDEO HOW TO REPLACE THEM. HOPE IT HELPS.

2 POSSIBLE PROBLEMS: 1ST - SPARK SWITCH ON ONE OF THE BURNERS GOT STUCK, OR 2ND - SPARK MODULE IS BAD. HERE IS THE VIDEO INSTRUCTION HOW TO DISASSEMBLE KITCHENAID COOKTOPS AND HOW TO REPLACE THOSE PARTS. HOPE IT HELPS.

Hi nancypp,

The ignition switches probably got wet.

Please follow my below Tip on how to fix it:

GAS STOVE CLICKING PROBLEM...

Kind Regards

JEDEMEYER1

* If this solution helped you, please accept it