Top 20 Jensen Iso-Max Stereo Line Output Isolator 1 to 1 Ratio Car Audio Amplifier Questions & Answers

Common fault but as others have suggested, check aerial plug. It does fall out, speed humps vibration,cause it to come out of it's socket.If not this, try a seperate aerial such as a piece of wire or a small screw driver blade in the hole. Press search and see if radio finds a station and locks on.If it does then you know you have an aerial problem and your radio unit is ok. Sadly, if no luck and no result then the only answer is to relpace the unit as it is not servicable.These can be found at some car breakers but take your car and make sure that you buy a tried and tested unit with its pin No. Typical costs are £30 with casette and £70 for cd player.

However because there are so many different types of socket and plug arrangments on these units and they all look alike , don't be tempted to part with any cash until you have got the correct one that fits your car and it works. If does and you have its pin, it will have to be entered to make it work and you have made a written note of it in your Ford hand book , then pay the man. Good luck From been there and have the tee shirt. J.R. Note. Halfords do a fitted alternative replacement for around £150 if no luck and you are prepared to spend that kund of money.

Do the Screen Calibration. https://www.google.com/search?q=Jensen+9022+touch+screen+is+out+of+alignment ..

Try Jensen support for that detail. https://jensenmobile.com/support/ https://jensenmobile.com/shop/multimedia/cr271ml/

It sounds like there may be an issue with the mechanical components of the DVD player, specifically with the tray. Here are some troubleshooting steps you can try:

1. Check to see if the emergency eject feature is working. There should be a small hole on the front of the DVD player, and you can use a paperclip or a similarly sized object to push the button inside. This should manually eject the tray.
2. Make sure that the DVD player is receiving power. Double-check all of the connections and fuses.
3. Reset the DVD player by disconnecting the power for a few minutes, then reconnecting it and trying again.
4. If none of the above steps work, it may be necessary to take the DVD player apart and check the mechanical components for damage or wear. However, this is not recommended unless you have experience with electronics repair.

If none of these steps resolve the issue, you may need to seek the assistance of a professional electronics repair technician.

This video may help you https://www.youtube.com/watch?v=VC89DgWJlYw

1200 Watts at 12volts is 100 Amps. At least 16mm on a short run.

Your Jenson model as written only appears here on Fixya in your question. The Jenson modelling numbers don't follow what you wrote so your model number 'EOA 7P' is not valid. https://www.google.com/search?q=jensen+eoa+7p ..

hair dryer if just moisture if water [failed seal or damaged cover ] and need to unscrew ans pry apart --but if water most likely electric circuit damage

No, you cannot use a 270 watt amp kit on a 1000 watt amp. The wattage of the amp kit must be equal to or higher than the wattage of the amp it is being used for.

My guess would be internal short

Ground the parking brake wire

Your extension voltage has a problem

There is always a chance that you "bricked" the unit with the update. IT happens. When you get to the cross hairs you are supposed to hold your finger in the middle till it asks for the next step. IF it wont go to this, then can you retry the whole process over again. If not you have bricked it and it has to be sent in for reflash

YOU HAVE TO GO INTO THE MENU SETTING

Ribbon from player to screen not properly connected or broken due to unfolding and folding.

i searched and found the diagram for you hope it helps.

https://pdf.crutchfieldonline.com/ImageBank/v20170729101300/Manuals/110/110VX7023.PDF

try code '''0000'' or 1234'''

it is not difficult.... why uploading these questions...