20 Most Recent KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher - Page 7 Questions & Answers

I had the same problem with my dishwasher. I have model number kudso2frss4. My husband and Father-in-law checked all the electrical and they were all fine. They found that the high-limit tub thermostat was bad. They bypassed it with a wire until the part comes in. It is working great now. Hope it helps good luck

the white hook peice is just that, a clip to hld down the motor. as you reinstalled you must have twisted or shifted housing to "pop" that clip. no worries easy fix. remove the lower rack and give alook at the motor assy from within ther tub make sure the black gasket is pushed completely down flush with the bottom of the d/w. applying pressure to top of motor assy will push it flush. the motor simply rests in the opening . the clip holds it in place from underneath, unable to find a pic but there a 3 in total under unit.

This motor comes as a module. The whole plastic assembly its in is part of the module. It comes out with 3 slide out releases around edge of module underneath.

DONT KNOW THIS UNIT BUT TRACE BACK YOUR STEPS. CHECK THE PRESSURE SWITCH FOR AN AIR BUBBLE AS THERE SHOULD BE NO ACTION WITH THE ROTORS UNTILL YOUR WATER LEVEL IS CORRECT.CHECK IF THE SUMP LIMIT ISNT STICKING.

Salvy, see if you can get out of that fault by pressing, in this order within 6 seconds. Heated dry-normal-heated dry-normal. If you don't have those keys try- high temp-air dry-high temp-air dry. This is the service cycle, all lights should light up and the unit should go into a self test and clear the fault. The test lasts for about 25 minutes. Let us know it this works, Catriver..post back.

here is a link to installation copy and paste https://www.manualslib.com/manual/931286/Kitchenaid-Kgct305bwh0.html?page=2#manual

It sounds like the water inlet valve has stopped letting water in. With no water the spray bar won't rotate as it is driven by the pump. Generic videos.

Same issue here. WHAT WORKED FOR ME was simply unplugging the dishwasher for 15 seconds (no idea if 15s necessary), and plugging back in. Viola!

If the hole is small you can seal it with epoxy putty. Clean and abrade the area and after mixing the putty make sure it is pushed well into the hole and if possible smoothed over on the underside. Two types that will work.

J-B Weld Waterweld Epoxy Putty, 57-g ' Canadian Tire

https://www.canadiantire.ca > ... > Adhesives Waterweld Epoxy Putty allows you to make permanent repairs in moist or under water applications,Will fully cure in 60 minutes and will adhere to most ... Rating: 4.2 · ‎106 reviews

• J-B Weld SteelStik Epoxy Putty Stick, 57-g ' Canadian Tire

  https://www.canadiantire.ca > ... > Adhesives J-B Weld SteelStik Epoxy Putty is a steel-reinforced epoxy putty stick that is great for use on automotive and machine parts, exhaust systems, plumbing, .. ..

I couldn’t find any error code 2H but I did find an error code H2O. This code means insufficient water pressure. If the display reads 2H, it usually means the start delay function is turned on. The dishwasher will turn on in 2 hours if door is closed. This dishwasher is advanced. To understand all operations you should read the user guide or manual.

Do a hard reset and it should work..if not then replace the control board. http://www.ehow.com/how_7488137_reset-kud101flss6-dishwasher-control-lock.html

Pick any 3 consecutive keys (except Start or Cancel, then press them in the sequence 1, 2, 3, 1, 2, 3, 1, 2, 3. The dishwasher will go through a self-test and short cycle, and reset itself.

Question edited for clarity. Question moved from Miscellaneous. Create upward pressure as you are undoing it. You may be able to make it grip.

possible flood switch stuck

Try a Power Reset. Before you go to bed, cut the power to it using the breaker, the plug, or isolation switch. Try next dinner time. Press and Hold the On switch before you turn it back on to fully dissipate power. Other ideas https://www.google.com/search?q=KitchenAid+Superba+Monterey+21%2C+Model+KDSM-21A+not+pumping+out+at+the+end+of+the+cycle ..

I had this exact same story with my new Whirlpool dishwasher. My daughter fell on the open dishwasher door and afterwards it wouldn't latch closed. After researching online, I learned that 90% of the time it's bent door hinges. At $$130 each, $260 total, I didn't want to replace the hinges. So I removed the hinges, took them downstairs to my shop, put them in the vise and straightened them back with a hammer. Just took a few good, solid hits on each hinge and they were straight again. I installed them back onto the dishwasher and it worked like a charm! Door latches just fine.