20 Most Recent Sanyo PLC XU48 Multimedia Projector - Page 9 Questions & Answers

You will need to navigate the menus. Locate the "Ceiling" option and turn it on. That will flip the image. You can reference this on page 49 of the manual which can be downloaded here:

http://www.projectorcentral.com/pdf/projector_manual_4932.pdf

Hope this helps,

Dan

make sure it's on computer (vga) and not component (rgb).

Please reply with the make and model.
Thanks!

what are you talking about? please clarify.

overheating. clean out projector with canned air. check the fans. reset the settings to factory default.

if you have an lcd projector, one of the light filters on the lcd panels is fried due to excessive dust and heat. unfortunately, you'll need to replace the whole optical engine. if you have a dlp projector, replace the colorwheel.

reset the lamp counter (menu-settings-lamp age-lamp counter reset-yes).

Have you tried changing the refresh rate. It is located under "Control Panel, Display, Setting, Advanced, Monitor" I have had some success trying this.

Good Luck

Sounds like the lamp is at the end of it's life. If the image has been getting harder to see/dim, I would say it's the lamp.

I am researching this further but have you tried the simple shut down the unit, then unplug it from the wall for a few minutes, then plug it back in. Try reprogramming it after that.

Please let me know

Thanks
Tim

Hi

Thanks for using FixYa. Are you using the same type of input & output cables from the projector(like RCA or DVI or S-Video)?

If not then please use the same type of cables everywhere as a delay is caused while processing the analog signals if fed through the RCA cables than a Digital(DVI) cable.

Also confirm that if you are using two projectors fed with the same input then you'll need a dual switcher if you need any of the content to be on the second screen. Or if you want to have the second projector as a confidence monitor, or something that only projects what you want directly from the camera, then your second projector can go direct from a second video card to the projector using a VGA feed.
Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee

Hi there

If the temp light is showing from startup and doesn't fire up at all - you might be facing a Mainboard fault.This will need either repair or replacement.Must warn you that the replacement of a Mainboard is very expensive.

thank u
rate me!!

canned air. wiping the mirror could scratch it.

200 ml is about 6.76 US ounces or about 7.04 UK ounces.

No money ever! There is no payment made for answers on Fixya, points don't mean prizes, they are just for fun. ADMIN Andrew

• Answers: 65,820 and not a penny per Answer.

Head over to www.justanswer.com they pay lots of money because they charge for people to ask a question. ..

'Make model (what it is)' is needed in questions like this, and in fact ALL questions!! But we can just guess.

Error Code Ir 3300 e350-3000 and e350-00002

Copytechnet https://www.copytechnet.com > ... > Canon May 1, 2018 - Put ALL the original boards back in the machine. Go to service mode level 2 & perform E355 clear. If this fails your machine is scrap. CANON iR2200 Error code E000350-001 Jan 22, 2007 error code :E0003-0002 canon IR 2880i Feb 5, 2018 Canon IRA C5540I Code E000354-0002 Sep 23, 2021 E000350-3000 on IRC4580 Sep 25, 2017 More results from www.copytechnet.com

Canon iR Advance 4245 - E350-0002

PrintCopy .info https://printcopy.info > code=E350-0002 Canon iR Advance 4245 ; Code: E350-0002 ; Description: System error ; Remedy: Contact to the sales companies. ..

This link is the best I can come up with: How to fix E6 & E7 on Trojan treadmill solved!! (youtube.com)

I need help I have an error on my ComColor 7050 Z08-1090

Call your supply company.

The series on the following link includes the model you are asking about. EMERSON FINCOR 2330MKII SERIES EQUIPMENT MANUAL Pdf Download ' ManualsLib