20 Most Recent Motorola Mobility H300 Wireless Headset - Page 4 Questions & Answers

Is the battery full charged? Is it a new battery or an old one? Have you tried to replace the battery?

I have a Blackberry curve and i use this headset. You just hold in the key to your bluetooth till it stays solid blue light, then go on your blackberry under "options" then "bluetooth" then search or add new device. it will search it, pascode is "0000" should load up then. then everytime u put ur bluetooth on and hit the button to turn it on ur blackberry will pop up and ask if you want to use it, just hit yes and your good to go.

Mike

if you never reset it when you purchased it try using the code 1111, or 1234 or 2222, etc shouldnt go higher than 5555...those are Moto's default sec settings. hope this info was helpful:)

The button on the face of the headset (same one that turns it on/off.
Make sure it is off. Now turn it on by holding the button down untill the light blinks rapidly then stays on steady.

Yes It is 0000

try 0000 (four zeros)
it is normally the default

try these codes one of them should be the right one.

0000
1234
4321
6789
9876
1111
9999


hope this helped
please rate well If you need further help, reach me via phone at https://www.6ya.com/expert/mark_445a24324be9eb03

Passkey should be 0000 or 0123. These are the most common codes on bluetooth devices. Should work!

Hold down the power button untill the light remains on.
This setts the device to "Find Me".

pass key 0000
for more clear instructions go here
http://www.motorola.com/mdirect/manuals/QG-H300_9495A08A.pdf

With the headset power off, press and hold
the Call button for 6 to 10 seconds until the
blue indicator light turns on and remains
steadily lit. (The light will flash while you
hold the Call button.)

If the indicator light is flashing or does not
remain steadily lit, turn off the headset and
repeat step 1.

Before you can use your headset, you must
pair (link) it with your phone.

Step A - PUT HEADSET IN PAIRING MODE
Note: To turn off headset, see "Turning On and Off" on the
reverse side of this guide.

PAIR
Your Phone
Select (Menu) > Settings > Connection >
Bluetooth Link > Handsfree > Look for Devices.
The phone lists all Bluetooth devices it finds.
Select Motorola H300.

Press OK or Yes to pair (link) the handsfree
device.

Enter the passkey 0000 and press OK.
Note: Passkey cannot be changed
from 0000.

Step B - SET THE PHONE TO LOOK FOR
YOUR HEADSET

1.Press and hold the Multifunction button in the middle of a boom headset while the headset is closed. The light will glow blue.2.Open the boom microphone and the blue light should remain on. If not, repeat step 1.
3.On the cell phone, press Menu > Settings > Connection > Bluetooth > Handsfree > New Device
4.Select H300 once a connection is detected.
5.The passkey "0000" is now entered to confirm the connection has been made.
6.The cell phone screen will now read "Bluetooth Connection".

Tips:
1.Provided you set the Bluetooth power to "On" after the initial connection has been made, the phone will automatically re-connect to the headset.
2.To set the Bluetooth power on - Press Menu, Select Settings, then Connections, then Bluetooth link, scroll to Setup and select that. Scroll to Power and chose Change. Scroll to On and press Select. The screen should now read "Changed: Power On".
3.Test Your Connection: Close the headset and watch for cell phone to say "Disconnected". Re-open the headset and the phone should be connected automatically and will now display "Bluetooth Connected".

please give good rating if the solution works.
Thanks for using FixYa.

for more clear instructions go here
http://www.motorola.com/mdirect/manuals/QG-H300_9495A08A.pdf

With the headset power off, press and hold
the Call button for 6 to 10 seconds until the
blue indicator light turns on and remains
steadily lit. (The light will flash while you
hold the Call button.)

If the indicator light is flashing or does not
remain steadily lit, turn off the headset and
repeat step 1.

Before you can use your headset, you must
pair (link) it with your phone.

Step A - PUT HEADSET IN PAIRING MODE
Note: To turn off headset, see "Turning On and Off" on the
reverse side of this guide.

PAIR
Your Phone
Select (Menu) > Settings > Connection >
Bluetooth Link > Handsfree > Look for Devices.
The phone lists all Bluetooth devices it finds.
Select Motorola H300.

Press OK or Yes to pair (link) the handsfree
device.

Enter the passkey 0000 and press OK.
Note: Passkey cannot be changed
from 0000.

Step B - SET THE PHONE TO LOOK FOR
YOUR HEADSET

When your headset is successfully paired

the pass key is 0000

With the headset power off, press and hold
the Call button for 6 to 10 seconds until the
blue indicator light turns on and remains
steadily lit. (The light will flash while you
hold the Call button.)

If the indicator light is flashing or does not
remain steadily lit, turn off the headset and
repeat step 1.

Before you can use your headset, you must
pair (link) it with your phone.

Step A - PUT HEADSET IN PAIRING MODE
Note: To turn off headset, see "Turning On and Off" on the
reverse side of this guide.

PAIR
Your Phone
Select (Menu) > Settings > Connection >
Bluetooth Link > Handsfree > Look for Devices.
The phone lists all Bluetooth devices it finds.
Select Motorola H300.

Press OK or Yes to pair (link) the handsfree
device.

Enter the passkey 0000 and press OK.
Note: Passkey cannot be changed
from 0000.

Step B - SET THE PHONE TO LOOK FOR
YOUR HEADSET

When your headset is successfully paired

The quick answer is that you can put it into pairing mode, and your phone should recognize it. To put into pairing mode, push and hold the large power/answer button for at least 6 seconds. The light will start flashing, indicating that it is in pairing mode. Go into the Bluetooth menu on your phone and make sure Bluetooth is turned on, that your phone is visible, and that you can search for new headset devices. Make sure the headset is still flashing. When you discover the headset in the phone, it may prompt you for the code. I believe the pairing code is "0000". Add the device to the phone. You should now be able to use it with your phone.

If this doesn't get you there, do a search for H350 Manual to get a pdf of the user manual and quickStart guide.

The quick answer is that you can put it into pairing mode, and your phone should recognize it. To put into pairing mode, push and hold the large power/answer button for at least 6 seconds. The light will start flashing, indicating that it is in pairing mode. Go into the Bluetooth menu on your phone and make sure Bluetooth is turned on, that your phone is visible, and that you can search for new headset devices. Make sure the headset is still flashing. When you discover the headset in the phone, it may prompt you for the code. I believe the pairing code is "0000". Add the device to the phone. You should now be able to use it with your phone.

If this doesn't get you there, do a search for H350 Manual to get a pdf of the user manual and quickStart guide.

You have to hold the on button until it is a solid blue light not flashing 5 or 6 seconds then it is ready to be paired.

The pin number ginen in the instruction manual is 0000.

hold the button down until the light stays solid on the headset, power off, then hold down phone button, hold even after it turns on, blue light will stay solid. do this while serching with the ps3
my ps3 online is Meow_Meowz, let me know if that works for ya

Checked the volume on the headset? As well the volume on the phone

it is '0000', they are all the same