20 Most Recent
HP LaserJet 2840 Printer - Page 2 Questions & Answers
Half page printing
Normal
0
Driver could be corrupt.
Disconnect the printer or at least be sure it is turned off.
I'd do both and reinstall the CD software program that came with
the printer. When the software program asks you to connect the
printer to the USB port, do so and it should again work properly.
Hope this helps. Bud
HP LaserJet 2840: Page 'Too Complex'
We would like to inform you that the error you are getting is not because of the printer driver installed on your computer but due to the USB speed setting on the computer.
. Please perform the following steps on the printers control panel.
a) Press the Menu button.
b) Press 2 on your keypad and then you will see Secondary Service/Service Reports.
c) Press the right arrow button until High Speed USB appears.
d) Press the Enter button.
e) Press the right arrow button until OFF appears.
f) Press the Enter button.
Print something from the computer to test for the issue.
The first print after performing the steps will take a little time to print but the remaining page will print in the normal speed.
Selection to turn off high speed USB clears out the memory and next print jobs works better, because the memory is no longer fragmented.
3. If the error persists, please perform the below steps:
NOTE: If possible, print a configuration page and menu map prior to performing a cold reset.
This will document the current settings for later reference as performing factory default settings will clear all the information stored in the printer.
Perform the following steps to restore the factory defaults using the device control panel.
a) Press the Menu button on the device control panel.
b) Use the < (Left Arrow) or > (Right Arrow) button to select Service, and then press the Enter button.
c) Use the < (Left Arrow) or > (Right Arrow) button to select Restore Defaults, and then press the Enter button. The device setting will revert back to the factory default settings and the device will restart.
When printing it says
check the printing file size. Also check that USB high speed is set to "off" in the secondary service menu. Default is "on" and can cause this message.
To enter the menu press "Menu" key followed by the "2" key and scroll to the USB setting.
Getting "Page too complex" message
fixing this one is easy. Go to the unit and press the menu. Then with the arrows go to service and press ok / enter, with the arrows look for high speed usb and press enter, then look for ''off'' and press enter. The unit will reboot and you will be able to print
HP 2840
Go to Service section from the Main Menu then go to "High-Speed USB" and set it to OFF
Message says page is too complex
In to the Service section from the Main Menu go to "High-Speed USB" and set it to OFF. This will help unless your document is using more than the printers ~45MB of usable memory.
I have an HP 2840
Have you tried simplifying the page to be printed? What memory is installed in the printer. You may need to upgrade the printer memory or the memory could be faulty.
Incorrect yellow what does it mean?
If it is a message on the control panel it means you have installed an incompatible cartridge, possibly for a similar series printer or maybe the id chip on the cartridge is bad.
Why is my paper coming out wrinkle Dell B1160W
Could be a number of factors.. first humidity affects paper, if there is moisture in your paper...caused by air conditioners constantly running .
check the paper by placing the back of your hand to the paper that is in the paper tray and or the package for a very cool feeling, this will definitely cause the paper to wrinkle when coming out of the fuser unit.
Also it could be charging of the paper during the transfer stage..which can be checked by starting a copy and trying to catch it before the paper enters the fuser rollers ..too late if it comes into contact with the upper and lower pressure rollers of the fuser unit.
Also the fuser unit definitely needs to be checked as a major source of wrinkling of copies..sometime the fuser roller will start loosing some of it's coating which you can easily check by viewing the condition of the upper roller.
Anyway it's either moisture in the paper, charging of the paper, or the fuser unit is the probable suspect.. check them all. If you need further help, reach me via phone at
https://www.6ya.com/expert/howard_563901c2e8628759
Why HP probook 6470b is saying Memory is low
4gb of ram is enough for most casual machines, unless you are running numerous programs the physical ram shouldn't be an issue.
Try increasing the paging file size and increase the amount of virtual memory the machine can borrow from the hdd. Both of these options can be accessed by right clicking on an empty area of the desktop and clicking on properties. If your primary hdd is almost full this could be another reason why you are running low on virtual memory. Hope this helps
Hp 2840
This printer has the rotating carousel assembly and therefore it is susceptible to becoming misaligned very easy and this could be the source of your scanner errors. More than likely of an inserting the wrong cartridge into the carousel...it can be fixed but judging by the age of this printer and the amount of labor to repair I would just junk this because of the time and labor involved ..plus there are definitely more productive and efficient models for a very low cost that will do you some justice.. that's just my opinion. If you need further help, reach me via phone at
https://www.6ya.com/expert/howard_563901c2e8628759
Incorrect Yellow
Are U installed specified yellow cartridge? Chk with old cartridge & chk for the message.. Same error? there is a mechanical issue, carousel unit might be misaligned..To align it technical skills required, better go to the nearest service center.
If different error replace with another cartridge.
Not finding what you are looking for?