20 Most Recent Epson Perfection 3490 PHOTO Flatbed Scanner - Page 5 Questions & Answers

If you have already checked for paper jams and followed the instructions in the documentation without success, there are a few additional steps you can try:

1. Turn off the printer and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on again.
2. Make sure that the ink cartridges are properly installed and that they have ink in them. Replace any empty cartridges.
3. Clean the printhead. On the printer control panel, go to Setup > Maintenance > Printhead Nozzle Check. Follow the instructions to print a nozzle check pattern. If the pattern is incomplete or has gaps, select Clean the Printhead.
4. Reset the printer. On the printer control panel, go to Setup > Restore Default Settings > Reset All Settings. This will reset the printer to its factory default settings.

If none of these steps work, it may be necessary to contact Epson support for further assistance or repair options.

The Epson L382 printer does not have a physical reset button. However, you can reset the printer by following these steps:

1. Turn off the printer and unplug it from the power source.
2. Press and hold the "Stop" button, "B&W" button, and "Color" button all at the same time.
3. While holding the buttons, plug the printer back into the power source.
4. Continue to hold the buttons until the power light and the ink light start flashing simultaneously.
5. Release the buttons and press the "Color" button to reset the printer.

The printer should now be reset and the error message should be cleared.

The E-01 error on an Epson XP-305 printer indicates a paper jam or a mechanical issue with the printer. Here are some steps you can try to resolve the issue:

1. Turn off the printer and unplug it from the power source.
2. Open the printer cover and remove any jammed paper or foreign objects. Check for any torn pieces of paper or debris that may be obstructing the printer carriage.
3. Close the printer cover and plug the printer back in.
4. Turn the printer on and see if the error message has cleared. If the error persists, try the following steps:
5. Make sure the paper is loaded correctly in the printer tray and that the tray is not overloaded. Adjust the paper guides to fit the size of the paper you are using.
6. Try resetting the printer by pressing and holding the Stop button for 3 seconds.
7. If the problem persists, you may need to contact Epson support or a qualified technician for further assistance.

Swapping heads on Epson Stylus Pro 4450 and 9400 printers can be a complex and delicate process that requires a certain level of expertise and technical knowledge. It is recommended that this task be performed by a trained and certified Epson technician to avoid causing any damage to the printer or the print head. If you still want to proceed with swapping the heads yourself, it is important to follow the manufacturer's guidelines and safety precautions. The process generally involves the following steps: Power off the printer and unplug it from the power source. Remove the ink cartridges and any other components that may be in the way of the print head. Use a screwdriver to loosen the screws that secure the print head in place. Carefully remove the old print head from the printer, taking care not to damage any of the other components. Insert the new print head into the printer, making sure it is properly aligned and secured with the screws. Reinstall any components that were removed earlier, including the ink cartridges. Power on the printer and perform a test print to ensure everything is working properly. Keep in mind that swapping heads on your printer may void the warranty and can potentially cause irreparable damage. It is always best to seek professional assistance if you are not confident in your abilities to perform the task safely and correctly.

The error message you are receiving on your Epson DS 530 scanner is related to the network adapter. Here are a few troubleshooting steps you can try:

1. Check network connection: Make sure the scanner is properly connected to the network and the network settings are correct. Try restarting the scanner and the network router.
2. Restart the scanner and computer: Restart the scanner and the computer and try scanning again.
3. Update drivers: Check for any available updates for the scanner drivers and firmware. You can download the latest drivers and firmware from the Epson website.
4. Check scanner settings: Check the scanner settings to make sure the correct scan settings are selected. Make sure the scanner is set to the correct mode, such as color or black and white.
5. Try a different computer: If the scanner is connected to a network, try using a different computer to see if the issue is with the scanner or the computer.

If none of these steps resolve the issue, you may need to contact Epson support for further assistance.

To install Epson printer driver on Ubuntu, you can follow these steps:

1. Open the terminal on your Ubuntu system by pressing Ctrl + Alt + T.
2. Run the following command to update the list of available packages:

sql sudo apt-get update

1. Install the required packages for Epson printer drivers using the following command:

csharp sudo apt-get install printer-driver-escpr

1. Connect your Epson printer to your Ubuntu system using a USB cable or connect it to your network.
2. Go to the Printers settings by searching for "Printers" in the Activities menu or by navigating to Settings > Devices > Printers.
3. Click on the "Add" button to add your Epson printer.
4. Select your printer from the list of available printers and click on the "Forward" button.
5. Ubuntu will detect the drivers for your Epson printer and install them automatically.
6. Follow the prompts to complete the installation.

Once the installation is complete, you should be able to print from your Epson printer on Ubuntu.

The Epson EP 704A inkpad error message is an indication that the printer's ink pads are saturated with ink and need to be replaced. The ink pads are responsible for absorbing and collecting the excess ink that is generated during the printing process. To resolve this issue, you will need to either replace the ink pads or have them reset by an authorized Epson service center. It is not recommended to continue using the printer without addressing the inkpad error, as it may result in further damage to the printer. You can contact Epson support or a local Epson service center for further assistance with resolving the inkpad error on your Epson EP 704A printer.

Based on the symptoms you described, it sounds like there may be a timing issue with your Epson R1900 printer. The erratic spacing and repeated printing of the same image or text on the next line suggest that the paper advance mechanism is not functioning properly. This could be caused by a number of factors, including a worn or damaged paper feed roller, a misaligned paper feed mechanism, or a malfunctioning sensor that controls the paper advance timing. To troubleshoot this issue, you can try the following steps:

1. Check the paper feed roller for wear or damage. If it is worn or damaged, it may need to be replaced.
2. Check that the paper is loaded correctly in the printer, and that it is not jammed or wrinkled.
3. Check that the paper thickness setting in the printer driver matches the paper you are using.
4. Clean the paper feed mechanism and paper feed roller with a soft, lint-free cloth.
5. Reset the printer by turning it off, unplugging it from the power source, and leaving it unplugged for at least 10 minutes before plugging it back in and turning it on again.

If none of these steps resolve the issue, you may need to take your printer to a qualified technician for repair or replacement of faulty parts.

Error code 0xFB on an Epson PX660 printer indicates a communication error between the printer and the computer. Here are a few steps you can try to resolve the issue:

1. Turn off the printer and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on again.
2. Check that the USB cable connecting the printer to the computer is securely plugged in on both ends. You can try unplugging and plugging it back in.
3. If the printer is connected to the computer wirelessly, make sure it is connected to the correct network and the signal strength is strong enough.
4. Try restarting your computer to see if that resolves the communication issue.
5. If the above steps don't work, try uninstalling and reinstalling the printer driver on your computer.

If none of these steps resolve the issue, you may need to contact Epson customer support for further assistance.

You may be able to purchase an optical engine for your Epson EH-TW 8300 projector from Epson or from an authorized Epson dealer. You can visit the Epson website to find an authorized dealer or contact Epson customer support for assistance. Alternatively, you may be able to find a replacement optical engine from third-party suppliers or online marketplaces such as eBay or Amazon, but be cautious when purchasing from these sources to ensure that you are getting a genuine and compatible part.

It sounds like there may be an issue with the sensor that detects the maintenance tank. You can try resetting the printer's EEPROM by following these steps: Turn off the printer and unplug it from the power source. Hold down the paper source, paper feed, and cut/eject buttons simultaneously. While still holding down those buttons, plug the printer back in and turn it on. Continue holding down the buttons until the paper feed light starts flashing. Release the buttons and wait for the printer to complete its startup routine. If that doesn't work, you may need to have the printer serviced to fix the sensor issue. It's possible that the sensor or its wiring may have become damaged or disconnected, and a technician would need to open up the printer to diagnose and repair the issue.

Print patches or banding can occur for various reasons in inkjet printing, including issues with the printhead, ink supply, media, or printer settings. Here are some possible causes and solutions to consider: Clogged or damaged printhead nozzles: Check the printhead nozzles for clogs or damage, which can cause missing or uneven ink droplets. Clean the printhead according to the manufacturer's instructions, and run a nozzle check to confirm that all nozzles are firing properly. Insufficient ink supply or pressure: Ensure that the ink cartridges or tanks are not running low or empty, and that the ink lines and filters are not clogged or kinked. Check the ink pressure and viscosity settings in the printer software or RIP, and adjust as needed for the ink type and media. Inconsistent media feed or movement: Check the media for wrinkles, creases, or other defects that could affect the ink adhesion or movement. Ensure that the media is loaded and aligned correctly, and that the platen or rollers are clean and free of debris or wear. Incorrect printer settings or profiles: Check the printer settings and color profiles for the specific media and ink being used, and adjust as needed for optimal print quality. Use a color calibration tool to create or verify the ICC profile for the printer and media combination. Environmental factors: Ensure that the printer is located in a stable environment with consistent temperature and humidity levels, and that the ink and media are stored and handled properly to avoid drying or contamination. By systematically checking these potential causes, you may be able to identify and resolve the issue with your print patches. If the problem persists, you may want to consult a qualified technician or service provider for further diagnosis and repair.

Epson Printer Error 0X9D message generally pops up due to problems with the connection of the printer. Otherwise, if you connect your printer with any virus-infected device, then the printer can behave weirdly. Moreover, corrupted system files also cause this kind of technical glitch in your system. If you are currently stuck with a similar error and wondering how to overcome this situation. Then, you can follow the instructions discussed below. So, without further delay, directly go towards the troubleshooting section. Like to Troubleshoot the error of Epson Printer Error 0X9D? Only follow the steps for Fix Epson Printer Error Code 0X9D posted on the blog. We offer online support in Printers Errors for any issue. Complete Answer is in Above Web Blog.

Question edited for a lot more clarity, full make model (what it is)'. Question moved to maker category. In the link https://www.google.com/search?q=printer+b310n+maintenance+box ..

If you have problems feeding paper, try these solutions: ·Make sure the paper cassette is inserted in a proper way. ·Check the paper size and type settings properly you loaded. ·If paper does not feed correctly, remove and reload it in the cassette and adjust the edge guides. Make sure the paper stack is not above the tab on the edge guides inside the cassette. ·If multiple pages feed at once, remove the paper, fan the edges to separate the sheets, and reload it. ·Do not load more than the recommended number of sheets. ·Make sure your paper meets the specifications for your product. ·If paper jams when you print on both sides of the paper, try loading fewer sheets. ·If too many pages are fed when you are performing manual 2-sided printing, remove all other paper from the cassette before reloading the paper. I hope your problem will be resolved. If you need any help, you can directly contact Epson printer experts through Free Live Chat.

Epson SC-P607 - Error Code - Printcopy.info

https://printcopy.info > brand=Epson Code: 54H; Description: Sequence error. LD Roller reset error; Causes: • detection operation of ASF phase failure; Remedy: • ASF Assy • ASF Motor.

It is possible that your Epson WF-7820 is experiencing a paper jam or a misalignment of the paper cassette. If the paper cassette is not correctly inserted into the printer, the printer will display an error message that tells you to insert the cassette correctly. To resolve this issue, make sure the paper cassette is correctly inserted and that any paper jams are cleared. If the issue persists, try resetting the printer by unplugging it and then plugging it back in. If the error message still appears, contact Epson support for further assistance. Loading Paper in Cassette 1 (Upper Cassette) https://files.support.epson.com/docid/cpd3/cpd39348/Source/Printers/Source/Paper_Loading/Tasks/XP800/loading_paper_upper_xp800.htmlfaq-207896 ' SPT_C11CB58201 ' Epson WorkForce WF-7520 ... https://epson.com/faq/SPT_C11CB58201~faq-207896?faq_cat=faq-topFaqsWF-3820 Series User's Guide https://files.support.epson.com/docid/cpd5/cpd58812.pdf

If your Epson Stylus SX435W is indicating that there is no paper even though there is paper loaded, there could be several reasons for this issue. Here are some steps you can try to troubleshoot the problem:

1. Check that the paper is loaded correctly: Ensure that the paper is loaded into the printer's paper tray or cassette correctly. Make sure that the paper is aligned properly and not too tightly or too loosely loaded. Also, make sure that the paper is not curled or wrinkled.
2. Check for paper jams: If the printer sounds like the wheels are turning to engage the paper but the paper doesn't move, there may be a paper jam. Carefully check for any paper jams, and remove any paper that may be causing the problem.
3. Clean the paper feed rollers: Over time, the paper feed rollers can get dirty or covered in debris, causing them to slip and not grab the paper properly. Use a lint-free cloth dampened with water to clean the rollers. Be sure to let them dry completely before attempting to print again.
4. Reset the printer: Sometimes resetting the printer can clear any errors or issues that are causing the "paper out" message. Turn off the printer, unplug it from the power source, wait for a few minutes, and then plug it back in and turn it on again.

If none of these steps solve the problem, you may need to contact Epson support or take your printer to a service center for further assistance.

The error message you are seeing on your EPSON EX30 projector indicates that there is an issue with the Auto Iris function of the projector. The Auto Iris is responsible for adjusting the brightness of the projected image based on the lighting conditions in the room. If there is an issue with the Auto Iris function, it can cause the projector to malfunction and display error messages. To resolve this issue, you may try the following steps:

1. Turn off the projector and unplug it from the power source.
2. Wait for a few minutes and then plug the projector back in.
3. Turn on the projector and try to use it again to see if the error message has been resolved.

If the error message still persists after trying the above steps, it is recommended to contact your nearest Epson service provider for further assistance. They may be able to diagnose the issue and provide a solution, which could involve repairing or replacing the projector's Auto Iris mechanism.

Is the paper positioned in the proper spot? Most scanners require the paper is positioned at the bottom left. It also sounds like it may be the settings in your scanner properties. If it is set to detect the paper size, it will often choose a smaller size. Go inside the scanner properties and manually select the size paper you are scanning or select "scan to fit".