Top 20 Maytag Performa PAV2200 Questions & Answers

Try moving hot hose to the cold side and c old hose to hot side on supply side. this should correct your problem

if you go to this site there is a install video for your belt and model... http://www.appliancepartspros.com/whirlpool-whirlpool-dryer-belt-341241-ap2946843.html hope this helps cheers!

The switch the tube connects to shuts the water off. Will it cut off on high medium or low level. You can try blowing on the tube to see if it works. It should cut off when you blow.

is dryer drum turning u might be amotor are some other problem you may want to call a service tech to fix your dryer ok

A serious transmission problem, I doubt that it is worth the cost of repair, sorry.

The burning smell is your belt(s). Motor is turning but the transmission isn't causing the belt(s) to burn. From the sounds of it, it sounds like your transmission might be locking up. You can try to get the cabinet off of the machine and see if something is stuck in between the inner and outer tub.

Check that the exhaust hose is clean and not obstructed or kinked. Clean it from A to Z every six months! Does the dryer heating at all?? .

Faucet hoses are reversed, obvious!

A transmission problem, I doubt it is worth the repair cost.

could be a bad counter balance , u can remove the front panel and run a spin or wash cycle and listen to where its coming from so u don't have to replace all the balancers. on some models theres a heavy ceramic weight at bottom that at times goes bad and throws it off balance, just run it and look where noise is coming from

If you go to the following website and fill in the information it will give you an approximate age of your machine. You will also need your serial number as well as the model. http://www.appliance411.com/service/date-code.php

Likely bad board. May not be worth repairing depending on age/make/model of machine

As with most appliances and cars wiring harness are made to service many models for economy to the manufacture. One harness may have 50 wires in it but your washer may only use 30 of those wires. A wiring diagram is a must. If it did not come in the paper work that came with the washer you should be able to find it online. The last 2 washes I worked on had away to put them into a self diagnostic mode this may also be in your manuel. In both cases they had a no drain problem as the code stated and gave me a place to start and because of the way washers are made now adays the drain water pump gets clogged after so many seconds of not pumping it will shut the washer down. I guess to keep the motor from burning out. Taking the water pump assembly apart I found a sock yes a sock wrap around the impellers and this was in both washers. Removed the socks reassemble and both washers worked like new. this site might help you too. http://www.partselect.com/Models/LSE7804ACE/#Symptoms. I have a Maytag refrigerator never again from day one one problem after another. The Maytag of yesterday is no more.

if you can tip it up & see if its coming from the motor,pump of brake/clutch unit?? if none of those the maybe the main unit & it could be cheaper to buy a new one.

Check with the belt off that the bowl will turn freely, if not check drum bearings or something caught between inner & outer bowl. Make sure when you fit new belt it is adjusted to the right tension or it will slip & burn.

if u add an extension to the drain hose it will take a long time to and go down the pvc pipe. Just check for clog. by giving it for service one time may work.

You need to replace the top half of the agitator. Here is the part to order.

Slide the unit out from the wall and open the small access panel on the back, bottom left side. 98% of the noise problems from this model is do to the bad design on the drain pump which has since been redesigned and will need to be replaced. Here is the new pump.This washer pump has been redesigned by the manufacture. The mounting plate is no longer required. It now mounts directly to the base of the washer.

this is a washer so does not have drum rollers. clips to release front panel are at top of panel 2-3 inches in from both sides and need to be pushed in

you may havce a piece of clothing stuck between the outer and inner tub