20 Most Recent Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher - Page 9 Questions & Answers

There is often a filter inserted in the water feed pipe where it attaches to the machines valve and is part of the sealing washer, check that is also clear.

This is a computer error and really needs to be tested by an authorized repair company. There is one thing you might try and that is to unplug or cut the power to the unit for several minutes and see if it will reset.

https://www.bosch-home.com/za/service/get-support/manual-search Possible source of manuals from manufacturer web site.

It means that water is not getting to the dishwasher. Make sure your water valve is turned on all the way. If that's okay, then maybe your water supply hose got kinked when you pushed the dishwasher back in it's place. As a final check, turn off the water, disconnect the water supply hose at the dishwasher, and with the end of the hose sticking in a tall bucket, turn the water valve back on. You should have a good strong flow. If not, then your water valve (under the sink) is bad, and you will probably need to call a plumber, because the problem is not in your dishwasher.

Try the flow sensor which sits in the tank on the left handside

This is a common fault and apart from trying silicone sealant , it is beyond repair

An "E" on any appliance means error. perhaps your drainage needs cleaned out....

This is the control panel that causes this issue.

Here's a troubleshooting guide, it should help for starters: Common Bosch Dishwasher Problems And Solutions

You can always check out this troubleshooting guide, it should give you an overall overview of the situation and help out: Common Bosch Dishwasher Problems And Solutions

Here's a link to a Troubleshooting guide, let me know if you need anything else: Common Bosch Dishwasher Problems And Solutions

First, I'm not a BOSCH tech. I just installed an ELECTROLUX dishwasher last month and had a similar problem. We also have an older Kenmore dish washer in another part of the house. The Kenmore is at least 15 years old and the touch pads are very soft and easy to select. The new one did not select either. I have to firmly depress the pad (which seems to be a stiffer plastic) and make sure I'm pressing down on the right spot to get things to work. * I recently came across the same problem. Pressing buttons won't change the displayed setting and it seemed to be 'stuck' in one mode but I coudn't tell if it was in between a cycle or just stuck. I've found that holding the 'start' button down (firmly) for 10 seconds will cancel all functions and it went back to normal. Since then it gets stuck several times over the week. I don't know if one of the kids is opening it up as I only turn it on at night just before going to sleep. So, someone may be sneaking around for a mid nite kitchen raid. * If you still have problems then check your warranty as many of these machines have parts warranty for 3-5 years. The 'switch' section if bad must be completely replaced as it is all one piece. These membrane switches will get damaged from a sharp fingernail or using a knife or fork to force the button down. (happened with the Kenmore, Kids kept stabbing it to get it to turn on.) Aloha, ukeboy57

"water not draining" and "Not getting water" seem to be mutually exclusive. If it is not draining but the motor is running you need a pump replacement. If it isn't getting water you may need a water valve.

Control board ussue more likely blow out relay on control board

Fault Code E24 Symptom: Dishwasher not draining properly. Cause: Drain filters blocked. Action: Clean the filters. Go to:Why is My Bosch Dishwasher Not Draining? For more detailed codes see ... http://www.drdishwasher.com/troubleshooting/manufacturer/bosch/error-codes

You can google your question for answer About 15,800 results (0.65 seconds) Took about 2 seconds to find answer. Look in the instructions that came with unit. ttps://bosch-dishwasher-errors.com/bosch-dishwasher-error-code-e04/

John, you might have a problem with your dispenser mechanism. You can remove it from the door and inspect it to make sure the door spring and tripping mechanism are not damaged. If any of these items are damaged, you can buy them separately and save some money. If you can't trouble shoot these or the main unit mechanism is damaged, you just replace the complete unit. It is not difficult to replace the complete unit. This YouTube video can help. https://www.youtube.com/watch?v=MDideDjjuEU Good luck.

The only thing you can do is replace the dispenser - not a difficult task

If the display wont light up but the flood switch works (drain pump operates) then its most likey the Power module (right side rear) is faulty. You might want to try a reset - at the breaker disconnect for a few minutes then try again