20 Most Recent
Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher - Page 8 Questions & Answers
Display has error code h01
h:01 means 1 hour delay. Press the delay button repeatedly to get to h:00 then hit start.
9/16/2020 12:13:14 PM •
Bosch...
•
Answered
on Sep 16, 2020
How to clean bosh dishwasher inlet water filter
Most of these units have a waterproof solenoid inlet on the hose. If yours has this you can pull out the rubber washer in the end revealing a plastic mesh cover. This can also be pulled out with pliers. It can be a bit stiff to take care not to muller it!
Under the plastic mesh is also a restriction valve which helps to slow the water pressure down. This has a little plastic shaft with a small rubber seal around it and can also be pulled out and cleaned.
3/4/2020 7:35:35 AM •
Bosch...
•
Answered
on Mar 04, 2020
Bosch dishwasher E14 fault
Water protection system activated.Turn off water supply. Call customer service and quote the fault code.https://finderrorcode.com/bosch-dishwasher-error-codes.html
3/3/2020 11:11:55 AM •
Bosch...
•
Answered
on Mar 03, 2020
Just installed a new control panel on my bosch dw silence plus 44-dba and no lights on display panel come on,i have tried all power sources to the unit and all have power the door latch seems to be ok
Hello. The control panel most likely wasn't the problem...the main control board probably was blown out causing the user interface to remain off. What was the unit doing or not doing that made you replace the control panel?
BIG TIP--if you had a power interruption (such as lights dimming in the house--called a "brownout") or a full scale outage where the clocks reset, the main board very well could have been damaged by the current surge when the power came back on. *NORMALLY**, if the appliance wasn't damaged immediately, 4-6 weeks after the event, strange things will start happening or not happening with appliances because chips on the the board were damaged and start to fail. I tell all my customers to check into WHOLE HOUSE SURGE PROTECTORS--you can buy them at Lowe's or Home Depot and, your power company might install them on your house for a little extra on the bill each month--money well spent!
1/23/2020 5:47:22 PM •
Bosch...
•
Answered
on Jan 23, 2020
Bosch dishwasher arms not spinning
Hmmmmmmmm. If the water goes in and the pump starts yet there is no washing action I would suspect that you have an impeller failure. The impeller on Bosch dishwashers is a two piece unit and the plastic rivets slowly dissolve until he impeller fails in 2 pieces. The fix is a new impeller which is supplied with a new seal as well. I believe Bosch does this to avoid running so long without renewing the seal and having a leak. I can't think of any other reason to have a dishwasher soluble part for an impeller. It's a bit of a bit** to fix but there are good videos on utube.
11/16/2019 1:53:35 PM •
Bosch...
•
Answered
on Nov 16, 2019
Alarm e15
Bosch SMS Series Dishwasher Fault Codes
E15
Water in base
Float sensor in the base has been activated. You can try to empty the base and restart the dishwasher as you will find noted many times in the forums but, if there is a leak this error code will simply be displayed again, you must find the cause of the leak.
but if you have a different model it can be something else
10/15/2019 1:21:25 PM •
Bosch...
•
Answered
on Oct 15, 2019
Bosch dishwasher stuck on auto
Try unplugging your dishwasher for 15 seconds or more, and then plug it back in. If that doesn't fix the problem, or if the problem comes back within a day, then you probably have a bad control board, or else the Auto key is stuck closed (like it is pressed).
10/3/2019 6:06:53 AM •
Bosch...
•
Answered
on Oct 03, 2019
Not finding what you are looking for?