20 Most Recent Maytag Atlantis MAV6451 Top Load Washer - Page 5 Questions & Answers

IF IT FILLS AND DRAINS THAT MEANS THE BELT IS GOOD. THE ONLY THING LEFT IS THE TRANSMISSION. SOME OF THESE MODELS HAD A 10 YEAR PART ONLY WARRANTY. AS YOU SEE MY WASHER HAS 10 YEAR PART ONLY WARRANTY. HERE IS THE LINK TO CHECK YOURS. IN BOULDER, CO SERVICE CALL AND LABOR WILL COST 230.00
http://servicematters.com/warranty/warranty_main.htm
Gear / Gearcase Assembly / Transmission 12 months 120 months 01/01/1999 12/31/2005

Hi,
Here is a tip that will help you with that...

http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

heatman101

I assume that your saying this happens all the time and not just because you have too many clothes on one side of your washer. First make sure your washing machine is level and there is no problem with the feet. If that checks out take the cabinet off the washer and check the tub hold down springs/straps and make sure they are still attached....they can come loose or break. Hope this helps!

you may have broken the lid switch needs to be checked

This sound is an indication that the main bearing is failing, you will need a seal kit and bearing. It would be good to replace the Thrust bearing while in there too. Parts will run about $120.00 It is a pretty big job so to have an expert out and make the repair you are looking at about $175.00 labor. If the transmission were also bad which is a possibility if it is 10 years old or so you can add about $225.00 to the job.

Sorry to be the bearer of bad news here

Many Hardware stores have touchup paint in a small bottle with a brush (like nail polish.......Now there's an Idea!!!).........Nomess

Hi,
Thanks for writing to Fixya.com.

There are three basic things you need to verify for the reason for this imbalance.

• Balance the load
• Level the machine
• Inspect the water pump

Please check the article bellow to find the steps how to do these:
http://www.acmehowto.com/howto/appliance/washer/check/movement.php

Thanks for contacting Fixya and please accept the solution if it has helped you.

I think you have nailed it!!! They go bad on many machines.Replacements are often heavier than the original...Can't tell if they are bad sometimes till you actually remove them and sometimes the loop will break where the pin goes through.
I hope that this will help you to solve your problem!

Door lock replacement vid and more good stuff

Bonus stuff: Wax motor 101 featuring R11 and Q6 swap out and other cool stuff

Note: both the motor control and the central control has to know that the lock is in place, so the wax motor does 2 things! It locks the door and then sends info back to the central control and the motor control on various models. So the wax motor is crucial. A red wax motor is a new and improved wax motor. What other smart pills have I got? Let see: Neptune washer manuals
If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Most likely you have a timer failure. To fix you will need to replace the timer. I hope this helps. If I can help in any way please let me know.

Could you describe the noise you are hearing. This will help to determine what to look for.

Usually there is a clog or restriction in the stand pipe(drain pipe) causing water to not drain away.....Suggest drain-O products.
If you have a very long drain or the stand pipe is not above the water level in the tub you will want some type of air gap to prevent siphoning.(siphon break kit)

good luck

It sounds like you have either a bad bearing or more likely the transmission is going. Look to see if you have any oil leaking out of the transmission. If so, see if you can replace the seal that is leaking before the transmission goes completely. Good luck.

Sounds like the "Overload" has been "Tripped"? What does your manual say to do when that happens?, I think you have to lighten the load and reset/restart?

Make sure that the inlet hoses are connected to the correct inlet solenoid valve (located just inside the cabinet). If the hot water solenoid was passing water when not wanted, the washer would eventually overflow on to the floor. There may be a problem with the solenoid control circuits which may require professional help to diagnose.

you will need to replace the dryer drum glides on the drum front panel after front panel removal by removing the toe kick panel screws and removing panel this should let you do this w/o removing top cover

timer bad

The manufacturer recommends you tilt back the washer and spray some penetrating oil into and around the brake package to stop the squeal. If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

You should be able to remove / open the top control panel (rear top) screws and tip it out forward to gain access to the lid switch. Be careful of the small air line that goes to the pressure switch. If that comes unhooked your machine will over fill.

The water inlet valve on the back where the water supply hoses are connected is not closing all the way. Replace it.