Maytag 24 in. MDB9750AW Dishwasher - Page 3 - Answered Questions & Fixed issues
No lights are coming on seems to have no power and
I know this sounds silly but, check the level of the dishwasher, if the door does not shut exactly right with it level my lights wont work, I can move it slightly to the side and forward (leveling it up) and bingo I have power and lights.
Dom
Wet dishwashing soap
make sure that the you let the hot water run for 2-3 min to make sure it is hot going into machine or it will not break down the soap.if the dispenser is opening then it is a tempproblem. let me know if my assistance was any help with a 4 thumbs up post
My dishwasher does not clean. Food particles are
Yes.
The filter is located at the base of the unit.
Usually it has something to grab onto - just pull it straight up and out.
There may be a stainless steel grating and an inner fine filter to remove as well.
Empty contents into the bin, and clean all of these parts in the sink.
Then replace.
START BUTTOM DOES NOT WORK
ck your door inter lock . if latch is problem then panel won't work . ( you may have a panel problem . some times the ribbon wher it connects to the pc is not making good connecton .. ****
#3 light stuck on (heat)
To fix this issue qwith my dishwasher, i held the heated-dry button for 3 aseconds (light flassed while i was doing it), and the light cleared. I canceled the cycle and then was able to start it and and let it run normally.
How do I replace the latch on my maytag quiet
Unfortunately, the Maytag quiet series models have plastic latch handles that are prone to crack after time.
You should be able to order a replacement handle through a distribtor.
If you can, unlatch/open the door. Using a star screwdriver, unscrew all the screws on the inside of the door frame.
Once all the screws are removed you should be able to separate the inside of the door from the latch assembly.
From there you'll need to squeeze the latch handle together and replace it in. I'll warn you that it feels like you have to squeeze the thing so hard you might break/crack it on your own. It is a hard/tight fit if I remember correctly.
One last thing you may want to do to is check the food grinder in the middle of the washer. Sometimes the cracked pieces of the latch can end up there stuck in the grinder causing it to be louder than it should.
Hope this helped.
12/9/2009 5:35:16 PM •
Maytag 24 in....
•
Answered
on Dec 09, 2009
•
1,216 views
How do i change front panel on maytag dishwasher
There are a couple of ways. Forst, you may not have to do anything. If you want a great new addition to your kitchen, try www.applianceart.com. these covers are applied without removing the front door. They also have stainless metal ones. To remove the panel there are 2 screws on the sides of the doors. Once removed, the frame will come off and you will be able to slide the panel in and out. DONT LOSE ANY OF THE SCREWS They are not normal screws.
4/11/2010 4:26:03 PM •
Maytag 24 in....
•
Answered
on Apr 11, 2010
•
2,440 views
Stops after 2 minutes
check to see if your water is turned on first to unit second you may have a solenoid problem
with unit not sure without checking it
water inlet valves may be clogged
Water won't drain
Check the following to address this issue you are experiencing.
1. Air gap / Drain hoses
If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly.
If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher.
Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.
2. Broken belt
Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.
Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out.
3. Pump
Some models have two impellers inside the pump - one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components.
4. Drain solenoid
Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly.
5. Motor
If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.
Replace the motor if defective.
6. Timer
Replace if defective (note: uncommon problem).
Maytag dishwasher has a grinding sound during the
Hi
Many times a complaint of noises ( grinding or scraping ) can be traced to a cracked impeller in many of the common motor and pump assemblies used today. Sometimes a poor washing complaint is common after this wash impeller has cracked. Remove power first before investigating.
The motor shaft has started to rust and swells out and this swelling cracks the upper impeller. Most times a new seal and impeller kit can cure this complaint but sanding and cleaning of motor shaft is required before replacing the new seals and impellers.
Please do rate the solution as FixYa and revert for further assistance.
Thanks
Rylee
MAYTAG DISPOSAL UNDER SINK WON'T START
There is a metal conduit around a wire with an L shaped plug on the end.
This plug fits into the disposal, from underneath on the outside, so that the end faces the "gismo" which magnetically closes the connection.
Get under the sink and pull it out and examine it. If it looks OK put it back in as far as it goes. If this does not work you need to replace this part.
Larry
Maytag diswasher won't spray water
water level/float switch is stuck. (dishwasher is getting a indication the unit has enough water in it to operate)...repair/replace float switch, located in front right corner under bottom rack.
clarkco
Dishes come ot just like I put them in
Check that both spray bars are turning. They can both be easily removed.
Once removed, make sure they are not clogged with stuff to prevent them from turning.
I assume you can hear water spraying around inside when it's washing, and that the dishes do get wet, and water does get hot.
Soap dispenser requires water hitting on it to open.
Not finding what you are looking for?