Top 20 Maytag 24 in. MDB9750AW Dishwasher - Page 7 Questions & Answers

If the door will not latch them the dishwasher is not going to work fix the latch.

A defective panel circuit board.

http://www.appliancepartspros.com/whirlpool-filter-pump-wp99001791-ap6014379.html Watch the video on the page

The filters are probably plugged. This will require removing the lower spray arm and cleaning the screens or its possible your not getting enough water in the dishwasher which will cause th upper spray arm to not turn

Replace the rinse relay

Check the drain line from the washer out, to the drain in the sink. Some how the restriction is causing residue to backup and your not getting a free flow out to the drain. If its a HOSE, disconnect it and blow it out with a vacuum and replace again.

Adrin, you might want to try this site repairclinic.com for parts.. https://www.youtube.com/watch?v=R0NHki-NnHg video probably broken latch or bad hinges .hope this helps a little

sounds like the pump is shot.

Unplug from power and see if this resets the control panel. Good luck.

Perhaps a safety switch somewhere. I would check inside for a utensil that fell down into the impeller or the like. Also look at the door latch area; maybe a switch there is not closing properly.

There are several possible problems that could cause this. The first step to diagnose the problem is to disconnect the washer from power. You will probably need to shut power off at the circuit breaker panel and leave it shut off for at least three minutes. This ought to clear the memory of the logic board (computer) in the machine. When you reset the breaker, the machine could work. The problem could also be in the panel controls themselves and Maytag has replaced some of these panels. Your washer might be one that should have a new panel from Maytag and you can find this out by contacting Maytag through their website.

hi Christine. see if this link helps you out. portable maytag dishwasher is locked and cannot open it Google Search

there is one or more wire shorting out [frying]. If you can access the wiring system you will see the wire[s] that have been burnt through the plastic covering. You really shouldnt use it until you get it fixed as it could catch fire.You now have one or more exposed, "hot" wire being exposed to other wires when the machine is on. Plastic burns quite easily. Its not the element. Thats just an accumulation of "salts" from the dishwashing detergent. If you want you can gently wipe an element with a damp cloth. [do the same with your stove and oven elements too]

Get a hold of the company you bought it from. Should be under warranty.

That light will remain on until you remove the dishes that are in there so that you know what is inside is clean and not dirty.

Clean the mesh filter at the bottom of the tub.

Reset is by disconnecting the power to it. If it is hard wired into the electrical box, you have to shut of the breaker and then wait a minute and turn it back on. When you power it back, you should hear the pump come on for a minute as part of the diagnostic. If it does not come one, then you have to check the main control, the transformer, the control board.

switch your detergent

The Maytag spray arms always get clogged and stop spinning. There is no easy way to remove the food matter from the inside of the spray arm after it gets pretty filled....UNTIL NOW...Drill a 1/4" hole on each end of the spray arm on the top. This method works for either spray arm, but be careful to leave at least 1/8" of distance from the two small holes that spray out water, when you drill the hole. Then using a Dremel tapered stone grinding bit enlarge the hole to 5/16" to accommodate a stainless steel 5/16" plug with the inside hex head. Also use the fine thread, not the course thread, as it will screw more securely onto the thin stainless gage arm and will last. Grind to enlarge the hole a little at a time to make sure your plugs thread into the arm snugly. I have been using our modified arms on our Maytag for over a year and we now have consistently sparkling, clean dishes. We run the washer twice per day and clean out the arms at least once per week which takes only two or three minutes.

Hard to bend, but not impossible.