20 Most Recent Maytag 24 in. MDB9750AW Dishwasher - Page 5 Questions & Answers


you need a new control panel
i do these all the time
get a new control panel and your problem is solved

Maytag 24 in.... | Answered on Oct 08, 2009


There are a couple of ways to do this. The easiest one is to check out www.applianceart.com and they have many different options for "wrapping" the front of your dishwasher. They change it often so if you don't see it, call the company becuase I know they have it.

Maytag 24 in.... | Answered on Jul 11, 2009


check to see if your water is turned on first to unit second you may have a solenoid problem
with unit not sure without checking it
water inlet valves may be clogged

Maytag 24 in.... | Answered on Jun 11, 2009


Check the following to address this issue you are experiencing. 1. Air gap / Drain hoses If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly. If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher. Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug. 2. Broken belt Some dishwasher models use a belt to drive the pump. Replace the belt if found broken. Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out. 3. Pump Some models have two impellers inside the pump - one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components. 4. Drain solenoid Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly. 5. Motor If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor. Replace the motor if defective. 6. Timer Replace if defective (note: uncommon problem).

Maytag 24 in.... | Answered on Jun 03, 2009


Hi

Many times a complaint of noises ( grinding or scraping ) can be traced to a cracked impeller in many of the common motor and pump assemblies used today. Sometimes a poor washing complaint is common after this wash impeller has cracked. Remove power first before investigating.

bc03dd0.jpg
The motor shaft has started to rust and swells out and this swelling cracks the upper impeller. Most times a new seal and impeller kit can cure this complaint but sanding and cleaning of motor shaft is required before replacing the new seals and impellers.

Please do rate the solution as FixYa and revert for further assistance.

Thanks
Rylee

Maytag 24 in.... | Answered on Jun 03, 2009


There is a metal conduit around a wire with an L shaped plug on the end.

This plug fits into the disposal, from underneath on the outside, so that the end faces the "gismo" which magnetically closes the connection.

Get under the sink and pull it out and examine it. If it looks OK put it back in as far as it goes. If this does not work you need to replace this part.

Larry

Maytag 24 in.... | Answered on Jun 02, 2009


the buttons to start the cycle auto clean or heavy wash does not light up and therefore is not cleaning my disches please advise to

Carol @ killday@irtc.net

Maytag 24 in.... | Answered on May 10, 2009

Tip

Dish soap in your dishwasher?


Don't use regular dish soap in your dishwasher; It was cause it to fill up with A LOT of foam. If you've accidentally done it, don't worry: First drain as much as you can. You can use salt to dissolve it. Then just run the machine with some cooking oil or vinegar. It will get rid of the mess.

on Mar 30, 2009 | Maytag 24 in. MDB9750AW Dishwasher


water level/float switch is stuck. (dishwasher is getting a indication the unit has enough water in it to operate)...repair/replace float switch, located in front right corner under bottom rack.

clarkco

Maytag 24 in.... | Answered on Feb 28, 2009


My guess is the stacking of the dishes. Make sure not to have them touching each other, and don't load so that a dish, bowl, or pot etc. is blocking a central water jet...

Maytag 24 in.... | Answered on Feb 08, 2009


Check that both spray bars are turning. They can both be easily removed.

Once removed, make sure they are not clogged with stuff to prevent them from turning.

I assume you can hear water spraying around inside when it's washing, and that the dishes do get wet, and water does get hot.

Soap dispenser requires water hitting on it to open.

Maytag 24 in.... | Answered on Jan 29, 2009


I did not use your service to fix my problem - I found the answer on Maytag.com. But you charged me anyway - so I would like that money refunded.

Maytag 24 in.... | Answered on Sep 05, 2008


all direction are on display when you close check a light comes its secure
of course after you put detergent open the fawcet water inlet

if any warm light on check the status probably you hava a damage switch door

Maytag... | Answered on May 01, 2019


Try pulling out maximum distance and then lift up at the front and then slide toward you.

Maytag... | Answered on Apr 21, 2019


Most likely the control panel is defective.

Maytag... | Answered on Apr 05, 2019


The Maytag spray arms always get clogged and stop spinning. There is no easy way to remove the food matter from the inside of the spray arm after it gets pretty filled....UNTIL NOW...Drill a 1/4" hole on each end of the spray arm on the top. This method works for either spray arm, but be careful to leave at least 1/8" of distance from the two small holes that spray out water, when you drill the hole. Then using a Dremel tapered stone grinding bit enlarge the hole to 5/16" to accommodate a stainless steel 5/16" plug with the inside hex head. Also use the fine thread, not the course thread, as it will screw more securely onto the thin stainless gage arm and will last. Grind to enlarge the hole a little at a time to make sure your plugs thread into the arm snugly. I have been using our modified arms on our Maytag for over a year and we now have consistently sparkling, clean dishes. We run the washer twice per day and clean out the arms at least once per week which takes only two or three minutes.

Maytag... | Answered on Mar 31, 2019

Not finding what you are looking for?
Maytag 24 in. MDB9750AW Dishwasher Logo

133 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Dishwashers Experts

Carmen Mikulic

Level 2 Expert

415 Answers

Mike

Level 3 Expert

4357 Answers

Marvin
Marvin

Level 3 Expert

84619 Answers

Are you a Maytag Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maytag Dishwashers

  • Maytag Dishwashers

Most Popular Question

door falls down hard

  • Dishwashers
Loading...