20 Most Recent
Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher - Page 5 Questions & Answers
My dishwasher model #mdb4651wont shut off
Sorry I only have more questions. If you observe the following things it may help rule out the thermostat or heating element . There are similarities to my problem. My dishwasher run for 4 seconds and stops briefly and starts again and will do that for ever.
1. Will it run properly in RINSE ONLY mode?
2. Does it run constantly or stop /starts continuously?
3. Does the soap dispenser open?
4. Does the timer count down? Ie cycle reads 2H and counts down, at least on my model.
5. Finally noticing if all the normal sequencing is happening. Ie turns on, pump empties the dishwasher, fill occurs, arms spin, and so forth. you should be able hear the unit empty and refill again and the rinse light goes on.
Sorry I could'nt be more help but possibly we can help each other.
3/7/2020 4:35:24 PM •
Maytag...
•
Answered
on Mar 07, 2020
Maytag Dishwasher has all lights lit on the panel after reset.
I would try turning off all power to it for few minutes and see if it reset it’s self, before I go to any great expense.
Also I had a washer that quit working on one cycle but would work on the others, could try that as well. Hope this helps!
6/30/2019 3:32:05 AM •
Maytag...
•
Answered
on Jun 30, 2019
MY MAYTAG DISHWASHER MDBH969AWS1 IS FLASHING LIGHTS AND WONT RUN
First step is similar to a computer. Reboot. Turn off your dishwasher at the breaker box. Hopefully your electrician designated a separate breaker for your dishwasher, otherwise whatever else is on that breaker will be off. Shut the breaker off; wait 10-15 minutes; turn breaker back on. This will resolve many issues and is the first step to try.
6/8/2019 5:48:56 PM •
Maytag...
•
Answered
on Jun 08, 2019
Maytag Dishwasher W10199645 the top rack is not getting washed. Help needed.
The Maytag spray arms always get clogged and stop spinning. There is no easy way to remove the food matter from the inside of the spray arm after it gets pretty filled....UNTIL NOW...Drill a 1/4" hole on each end of the spray arm on the top. This method works for either spray arm, but be careful to leave at least 1/8" of distance from the two small holes that spray out water, when you drill the hole. Then using a Dremel tapered stone grinding bit enlarge the hole to 5/16" to accommodate a stainless steel 5/16" plug with the inside hex head. Also use the fine thread, not the course thread, as it will screw more securely onto the thin stainless gage arm and will last. Grind to enlarge the hole a little at a time to make sure your plugs thread into the arm snugly. I have been using our modified arms on our Maytag for over a year and we now have consistently sparkling, clean
dishes. We run the washer twice per day and clean out the arms at least once per week which takes only two or three minutes.
3/31/2019 5:49:42 AM •
Maytag...
•
Answered
on Mar 31, 2019
My Maytag Quite series 300 dishwasher comes on but when it goes to wash it starts to hum and will not start
I have an old GE that did the same thing, if I don't use it enough it will do the same thing. The hum is from the electric motor in the bottom trying to rotate. I don't know your machine but I assume they are all made closely the same. Remove the bottom cover. You should see the back of the motor and it will probably have some slots in the rear cover. Close the door and try to start it while looking through the rear slots. I saw mine turn like an 1/8 inch and stop. The first time it did this, I unplugged a connector feeding the motor, tried to start it to make sure it didn't do anything and then with a long thin screwdriver went to the slots to help turn the motor. The second time I discovered on the right side of the motor housing there was a small opening towards the front of the motor (rear of dishwasher) I was able to get my fingers in there and turn the motor a few times by hand, plug the connector back in and the dishwasher started right up. Seems like the engineers knew this could be a problem and left an access point for us (or dishwasher repairmen to use and charge us $80 or something)
3/3/2019 12:31:35 AM •
Maytag...
•
Answered
on Mar 03, 2019
Not finding what you are looking for?