20 Most Recent Jabra BT350 Bluetooth Headset Headset - Page 8 Questions & Answers

u cant

This is not actually a solution, but when I had the same problem with my Jabra (which I think is one of the best), I took it to my phone store and they synched it for me. Lots of navigating around and knowledge of a code to input. Screw it, let them do it!

usually it's 0000 or 1234

1.Press and hold the Multifunction button in the middle of a boom headset while the headset is closed. The light will glow blue.2.Open the boom microphone and the blue light should remain on. If not, repeat step 1.3.On the cell phone, press Menu > Settings > Connection > Bluetooth > Handsfree > New Device
4.Select BT350 once a connection is detected.
5.The passkey "0000" is now entered to confirm the connection has been made.
6.The cell phone screen will now read "Bluetooth Connection".

Tips:
1.Provided you set the Bluetooth power to "On" after the initial connection has been made, the phone will automatically re-connect to the headset.
2.To set the Bluetooth power on - Press Menu, Select Settings, then Connections, then Bluetooth link, scroll to Setup and select that. Scroll to Power and chose Change. Scroll to On and press Select. The screen should now read "Changed: Power On".
3.Test Your Connection: Close the headset and watch for cell phone to say "Disconnected". Re-open the headset and the phone should be connected automatically and will now display "Bluetooth Connected".

please give good rating if the solution works.
Thanks for using FixYa.

go to your phone tools and find voice command blue tooth and follow prompts . its all in the phone . the tooth is run by the phone. your blue tooth is only a reciever, the phone is the boss. good luck

hold call button down till it blinks, than youll get intermitant light for about 30 seconds, than youll know its on. to turn it on hold call button down till it starts blinking at least 6 seconds. to turn it off hold call button down , itll blink for about 3 seconds than move your thumb off and when it ceases to blink its off. good luck

light is suppose to go out after leaving charger. try holding call button down till light goes solid and than follow adding new device on tools in your cell. go to blue tooth and follow prompts , also pass key is 0000 or 1234. good luck and dont feel intimidated by it if your not used to it it will get better.

try sending it back where you got it and exchanging it. just ran into that with an h.s. 820. got it exchanged and now evey thing is jake. also try holding the call button down for 10 seconds if no go i feel your tooth has a lil problem. good luck.

hello. i belive its a pause in between rings and when answared it stops, go into your tools on phone and pull up rings and you should find inermitant rings, than shut that turkey off. ( dont look for turkey, it aint there) i had same problem once took me most of the night to figure it out. good luck.

hello mom. try putting your phone into activate new device and than your tooth into discover mode, than your phone will ask you for password key and put in 0000 and press the o.k. button and pair it. it works most of the time. good luck.

right out of the box i had the light flicker on me too. if you don't have warranty or receipt like i did try this. i'm not responsible if it doesn't work after!

peel off the blue part of plastic that has jabra on it. take a screwdriver and unscrew the star screws. take the cover off. using some wires, briefly connect a battery (i used a wireless drill battery) to the leads of the bluetooth battery. you'll see a spark.

now my thing is charging for the first time

On The Blue Tooth You Have To Hold The On Off Till The Light Flash's Blue Red Over And Over Then Search For It On Your Phone.
Once You Find It It Will Be Recognized For Now On. Just Hit The Button On The Blue Tooth One More Time To Stop The Sync Mode.

Hi,

Follow the steps below:
• Setting the headset into pairing mode
1) Ensure the headset is fully charged
2) The headset must be switch off
3) Press and hold the on button for around 8 seconds until the light flashes red-blue
4) The headset is now in pairing mode
• Searching for the headset on the phone
1) Go to “settings” or “connections”
2) Select Bluetooth, then options
3) Select Devices and click add
4) The phone should search for any available Bluetooth devices and display what was found
5) Select the Jabra device and click add
6) You will be required to enter in a pass code which is standard ‘0000’
7) If successful then the headset will start flashing BLUE every few seconds.

• The headset is now paired with the phone

Hope this helps

Chris (ziraffa)

Be careful of the earhook Jabra does not offer a replacement in the BT5010

it is 4 or 5 ZEROS

If it's a Motorola Passkey, enter 0000

You need to turn it on so you get the intermittent flashing blue light then hold down the + button and answer button at the same time until you get a solid blue light. Then get your device to search for the headset etc......

Usually to solve some pairing problems shut off bluetooth completely(no lights) Push and hold button until bluetooth comes on,flashes then steady light,you may have to hold button for ten seconds or more.Then put phone in pairing mode.
When asked for pass code enter 0000.Phone should show connected to bluetooth device.

dont go near your ps3