20 Most Recent Jabra BT350 Bluetooth Headset Headset - Page 2 Questions & Answers

use 0000 because all of the bluetooth heasets use this codes only definitely it will work

How do I have to set up my Jabra head set?

BT350 passcode is 4 zeros... > 0000

http://www.jabra.com/Sites/Jabra/ap-en/headsetsupport/pages/Knowledgebase.aspx?kbid=9042862d-c51f-4611-98f6-dfe338dbf3ca

Take the unit apart by heating the colored backing surrounding the on off button with a hair dryer ( this helps loosen the glue). The remove the two screws holding the two halves together. They are tors, but you can file down an eyeglass screwdriver as I did to get them out. Then carefully separate the two halves and find the battery ( big and silver). See the positive and negative markings on the battery? Take a common D cell battery ( I have even done it with AA) and jump your Jabra battery with the D cell being careful to keep the terminals in correct order. It may take two or three times of doing this to get the really stubborn ones to kick in. The jump only takes two or three seconds. Then disconnect the D battery and try to plug your charger in. It should now work fine. If not then give it another jump. Now reassemble your unit in the reverse order and remember to keep charging it every once and a while, or it will happen again. Hope this helps......Taco

Try 000 or 999, what make and model BT headset do you have?

With headset off... turn on bluetooth search from the phone.
Hold on button on headset until light turns solid blue. Then search for connection from phone. (code is 0000 (4zeros))

http://www.jabra.com/Sites/Jabra/ap-en/headsetsupport/pages/Knowledgebase.aspx?kbid=ee68a9ea-df26-4882-a7f8-a6cbcc42345c

Hi,

You can download and print the instruction manual in PDF format by clicking this link.

Adobe PDF Reader is required to view this manual. Download Adobe Reader

Hope this helps. Thanks for using FixYa.

just hold the power button of blutooth for 10 sec and reset and re pair again

I took my husband's suggestion and used 0000 and it worked. My husband claims it is the factory default for all bluetooth headsets. Try it and let us know if it works.

I had the same problem-- i asked a verizon wireless guy and he said it's almost always four or six zero's so "0000" or "000000". Hope it works for you!

The generic PIN (Which is what I'm guessing you need) for most bluetooth devices is either 0000, or 1234. Please try those and see if that solves your problem.

continously press the power button on the headset for 2 seconds and then try to search from the mobile

you can only use one digit number not four digit..to detect the bluetoot headset

This is what I did:
1. open the headset by following these steps:
http://www.instructables.com/id/Jabra-BT-350-Disassembly-and-Repair/
2. measure the voltage of the battery. If it is too low, the internal charger circuit may not like it. Mine was 2.6v.
3. Charge the battery "manually" by connecting to 3 serially connected rechargeable batteries (final voltage should be around 3.7v). Three NiMH AA batteries are fine.
4. Reassemble and hope your headset is back to business.

By putting the blue tooth device in discovery mode it will reset it then your will have to enter the manufactures factory pin pairing code,Most blue tooth manufactures use a 4 digit pin pairing code,they are as follows0000,1234,1111,or 9999 this should be the code you are looking for i hope this helps

http://www.jabra.com/sites/Jabra/GNimages/Products/WirelessHeadset/BT350/Documents/BT350_UM_NA_EN_491.pdf

well keeping it for long could be the problem here. batteries go extremely down and not even that charger would start it up to a level where it will begin normal charging no matter how long you leave it on charger. The only solution is having some kind of tech dismantle it access the rechargeable battery inside, boost its voltage or jump start it by directly connecting voltage on its terminals for about a minute then put it back. all should work then.

regards