20 Most Recent
Lexmark X3330 All-In-One InkJet Printer - Page 8 Questions & Answers
Reset ink levels
Please note that once a Lexmark cartridge is refilled, it can no longer register its ink level.Also, Lexmark does not recommend the use of refilled, re-manufactured or clone cartridges. You might not get the print quality you expect from the ink that is specially formulated by Lexmark.
How do i fix my LEXMARK X3430?
Leading cause of paper
jams is debris / foreign objects that accidentally fell into the paper feed
area. Please try this approach to fix the problem:
- Remove the sheets of paper from
the feeder.
- Grab a flashlight and look
inside the feeder for any debris or foreign objects.
- If you're willing and
physically able, you may also carefully turn the printer over. Any debris
should just freely roll out from the feeder.
- If feeder is clear, place the
printer on the table. Open the printer cover and remove the cartridges.
- Check the cartridge area for
any obstructions in the paper path.
- Close the printer cover.
- Re-brick your printer by
pulling out the power supply - the black box where the power cord is
plugged into. Re-plug after 30 seconds.
- When the printer turns on,
reinsert the cartridges and load some paper. Try to print again to verify
that the problem is fixed.
If that doesn't help, try to re-seat the cartridges by removing and re-inserting them into the printer. Make sure they are properly seated and secured.I hope this helps.
Printing
A quick fix for most communication errors can be achieved by
resetting the printer and/or rebooting the PC. Simply disconnect the printer
from your computer (if USB connected)> reboot your pc > unplug and
re-plug the printer into the power source to reset it. When the printer turns
on, reconnect it to your computer (if USB connected). Then try to print again
once the computer fully recognizes the USB connection or when the WiFi light on
the printer turns solid green (if WiFi connected.).
If that doesn't help, try the steps below:
- Disconnect the USB cable
connecting the printer from your computer.
- On your computer, go to Control
Panel > Printers and Faxes.
- Delete the Lexmark print
object.
- Reboot computer.
- Re-brick your printer by
pulling out the power supply - black box where the power cord is plugged
into on the back of the printer, and re-plug after 30 seconds.
- When the printer turns on,
reconnect it to the computer.
- Wait until your computer fully
recognizes the USB connection. To check, go to Control Panel > Printers
and Faxes. If you see a new Lexmark print object in the list, try to print
a document to verify that the problem is fixed.
Printing
What is the model of your Lexmark printer? This will help us give you a more direct instruction on how to fix the problem you're currently experiencing.Meanwhile, you can try to do a deep clean cartridge/printhead function on your printer to clear the cartridge/printhead nozzles from possible clogs and dirt.If it's more on communication issue, a quick fix for most communication errors can be achieved by resetting the
printer and/or rebooting the PC. Frequently, issues are caused simply by a
break in the signal sent from PC to printer or vice versa. Unplugging and
re-plugging the printer allows the small amount of on-board memory on the
printer to be cleared, with the result that the PC recognizes the machine
properly. Programs continuing to run in the background of the operating system
(OS) can cause the signal to be lost. Rebooting the PC ends all programs that
may be running and makes a 'clean' start, allowing the signal to be detected.
What should I do with my Lexmark printer x3430? It will not print an entire article. It will print only one page.
A quick fix for most communication errors can be achieved by
resetting the printer and/or rebooting the PC. Simply disconnect the printer
from your computer (if USB connected)> reboot your pc > unplug and
re-plug the printer into the power source to reset it. When the printer turns
on, reconnect it to your computer (if USB connected). Then try to print again
once the computer fully recognizes the USB connection or when the WiFi light on
the printer turns solid green (if WiFi connected.).
If that doesn't help, try the steps below:
- Disconnect the USB cable
connecting the printer from your computer.
- On your computer, go to Control
Panel > Printers and Faxes.
- Delete the Lexmark print
object.
- Reboot computer.
- Re-brick your printer by
pulling out the power supply - black box where the power cord is plugged
into on the back of the printer, and re-plug after 30 seconds.
- When the printer turns on,
reconnect it to the computer.
- Wait until your computer fully
recognizes the USB connection. To check, go to Control Panel > Printers
and Faxes. If you see a new Lexmark print object in the list, try to print
a document to verify that the problem is fixed.
You may also try to update your printer
driver by visiting the Lexmark website at http://bit.ly/AbnM39. Select your operating system,
download and execute the file. After the install process, try to print again.
Error 1200
The
problem could be due to a communication failure between one of the printheads
(cartridges) and the All-In One (AIO) or by a short in one if the printheads. Please follow the steps
below to identify and fix cartridge issues:
- Make sure the printer is on.
- Open the printer cover. The
print cartridge carrier moves and stops at the loading position, unless
the All-In-One is busy. Note: If the carrier does not automatically move
to the center, turn off the printer or unplug the printer from the power
source and then carefully slide the carrier to the center.
- Remove both cartridges from the
carrier.
- Close the printer cover.
- Re-brick your printer by
pulling out the power supply - black box behind the printer where the
power cord is plugged in to, and re-plug after 30 seconds.
- When the printer turns on,
reinsert one cartridge first. Close the printer cover and check for any
errors.
- If no error appears, reinsert
the other cartridge. Close the printer cover.
- Replace whichever cartridge is
causing the error to appear with a new genuine Lexmark cartridge. Try to
print a document again to verify that the problem is fixed.
Problem with the print head
If you're experiencing printhead error message on your Lexmark inkjet printer, make sure that your printer firmware is updated. A firmware update for your model addresses printhead issues. Please visit the Lexmark website to download and install the
Lexmark Firmware
Update. Select the corresponding firmware version for your model to start the download.Should the printhead problem continue, please contact Lexmark Technical Support Center for additional assistance.
Paper wont feed
Leading cause of paper
jams is debris / foreign objects that accidentally fell into the paper feed
area. Please try this approach to fix the problem:
- Remove the sheets of paper from
the feeder.
- Grab a flashlight and look
inside the feeder for any debris or foreign objects.
- If you're willing and
physically able, you may also carefully turn the printer over. Any debris
should just freely roll out from the feeder.
- If feeder is clear, place the
printer on the table. Open the printer cover and remove the cartridges.
- Check the cartridge area for
any obstructions in the paper path.
- Close the printer cover.
- Re-brick your printer by
pulling out the power supply - the black box where the power cord is
plugged into. Re-plug after 30 seconds.
- When the printer turns on,
reinsert the cartridges and load some paper. Try to print again to verify
that the problem is fixed.
Message on screen printer printhead error
A firmware update addresses printhead error problem on recent Lexmark printers. Please visit the Lexmark website to download and install the
Lexmark Firmware
Update . Select your corresponding model to start the download.Should the error continue to display on your printer, please contact Lexmark Technical Support Center for further assistance.
My prnter wont install
What kind of printer? USB printer? Disconnect the usb cable to your printer If it is a USB connected printer. Uninstall all printers. Shut off computer, connect usb cable to printer. Restart computer, it should prompt you that it found a new device and wants to install drivers for it. If that doesn't work you could go into printers under control panel and add a printer. If have had more luck with the restart and finding it on its own. I hope this may help you.
Lexmark s605 gateway not working solution?
Try to re-install the printer driver on your computer. You may visit the Lexmark website at
http://bit.ly/uViCt1.
Select your operating system > click on "FILTER" > click on the driver under Recommended Downloads > download and execute the file. Simply follow the instructions to complete the installation.
Not finding what you are looking for?