20 Most Recent Maytag MGR5750 Gas Kitchen Range - Page 7 Questions & Answers

Either an oven temperature sensor or a control issue

yes but only by professional gas fitters it is all done by different jet sizes and air shroud positioning

Look on bottom of door. Theres usually a slot.

Free Maytag manual online: https://www.manualslib.com/manual/507401/Maytag-Gemini-Mer6772.html MAYTAG Gemini MER6772 User Manual

Hello, Peg -I hope I am correct in thinking it is the hinge/s of the over door which squeak. If so . . .Purchase some WD-40 spray oil (either the smart straw product, 8 oz:https://www.wd40.com/products/multi-use/aerosol/smart-straw-8-ozor the EZ Reach product, 14.4 oz:https://www.wd40.com/products/multi-use/aerosol/ez-reach )or some other brand of penetrating oil and water-displacing spray.Follow the instructions here:http://www.ehow.co.uk/how_7804008_fix-squeaky-hinges-oven-door.htmlBest wishes.

No release, but you can try unplugging it for 5 minutes and see if it resets.

It sounds like the seal round door may be in need of renewing. .or the doors are not closing properly..

Usually, the constant beeping indicates a problem with a stuck key on the keypad or with the electronic control (clock) board. Sometimes, the beeps indicate an issue with the door closed/locked circuit. Maytag lists the F5 error as a watchdog circuit on the clock assembly control board detecting a problem with the range. First, try unplugging the range for at least 30 minutes. You may want to check the wiring at the door latch.Also check for a stuck keypad. After that, the solution is to replace the electronic control board and send it off for repair. You may want to consider replacing the appliance. It is expensive and the oven of your range won't be available during the repair. The parts diagram is available at Sears Parts Direct, https://www.searspartsdirect.com/model-number/cre9800ace/3048/0124111.html . The clock is part 14 on the Control Panel diagram and has a substituted RFR-CCS part number. This means that new replacement electronic controls are not available. I wish that I had better news for you. Cindy Wells

If your stove has an electrical cord then it will not light if the power is off. This is a safety gadget and after a number of years ago all stoves were made like this. The stoves with no cord should light with a match.

My calibrator is under the oven button. You have to pull this button off to find it.

• Oven calibration feature - This function allows you to calibrate your oven.
• Resolution: Refer to your Use & Care Guide for specific information.
• Try holding "more" and "bake" buttons for 10 seconds

http://www.kenzolashes.com/

the problem with the self clean feature is the oven gets up to 1000 degrees,this can and will over time damage the electronics in the oven,usually it takes out the clock assy. this is where all the oven functions are that control the oven,most likely this is what got damaged,after all the things i've seen working on ovens i will never self clean an oven,i use easy off,if you do use the self clean don't use it near holidays or any family functions,if you take out the clock assy. the day before say thanksgiving and the clock has to be ordered you won't be cooking for that day.next time send the full model number off of stove,usually you open the bottom draw under the oven door,look on the left side or right and you'll see a tag on the frame with model and serial numbers,you need the model number to order parts.good luck with your stove you can go here put your model number in to look up parts https://www.searspartsdirect.com/model/search.html?q=DGRSC

Hi Robin Basirico, this looks like an intermittent problem. Somewhere there must be a loose contact I would guess. Be patient, may be the problem never occur again, then you are lucky. But almost for sure, it will return. Then it is easier to locate the source of the problem. Kind regards, Dik