20 Most Recent
Maytag MER6772 Gemini Electric Kitchen Range - Page 6 Questions & Answers
Range displays error code f9-5
HI. This indicates that there are serious issues that concern the operational value of the main control abord(ERC/Clock).
This will require you to replace the ERC, asap.
ERC_(Electronic Range Control Board)
F9-5_Hardware conflict(watchdog)
Bottom Baking element not working
dmiller58
If all your connections are solid then your controller is defective. Did you get any faults before changing the element? Does the broil (one at the top of the oven) work?
Post a response
Regards
My maytag gemini oven has been stuck in sabbath
Hello,
This is from the Maytag website it explains how to cancel the sabbath mode;
To cancel the Sabbath Mode: Press the Clock pad for three seconds.
Or
After 72 hours, the Sabbath Mode will end.
- "SAb" will flash for five seconds.
- The time of day will return to the display.
NOTES:
- Sabbath Mode can be turned on at any time with or without the oven on.
- Sabbath Mode cannot be turned on if the keypads are locked out or when the door is locked.
- Most prompts and messages and all beeps are deactivated when Sabbath Mode is active.
- If the oven is baking when Sabbath Mode is set, the Bake icon will go out at the end of the baking cycle. There will be no audible beeps.
- If the oven light is desired while in Sabbath Mode, it must be turned on before the Sabbath Mode is started.
- When the Sabbath Mode is started, the temperature display will immediately show the set temperature, rather than the actual oven cavity temperature. No preheat beep will sound.
- The self-clean cycle and automatic door lock do not operate during the Sabbath Mode.
- Pressing the Cancel pad will cancel a Bake cycle, however the control will stay in the Sabbath Mode.
- If power fails, the oven will power up in Sabbath Mode with 72 hours remaining and no cycle active.
I hope this helps to return it to normal mode,
GENE
We replaced the upper sensor for the top oven.
Hi
F3-E1 Error indicates
a loose/broken wire on the oven temp sensor or the oven temp. sensor itself is
bad and should be replaced. To solve this issue test the oven temp. sensor, it
should read between 1080-1120 ohms, if the rating is more then that and the door
appears to be closing fine then it is the control board that is bad and should
be replaced. Hope this helps...please post back for further assistance.
Daniel
Getting tu the heating element on a maytage oven
Hello Jerry,That bake element is accessed from under the floor of the the oven...in th erear of the floor is a couple screws if ya remove those ya can pull up the the oven floor up and out from the rear to the front the bake element will under of that floor.BEFORE ATTEMPTING THAT BE SURE TO DISCONNECT POWER TO THE OVEN
It's displaying an error code - F9-2. What
Hi lyndakh7,
The F9:-4 error code description is Latch Unlock Lower. Check for obstruction in door lock mechanism.
Hope it helps.
Thank you for using FixYa.
(Positive feedback will be greatly appreciated.)
F1-4 Error message displayed
Hi jwill343,
The F1:-4 error code means "Runaway Clean Lower oven".`You need to check the oven temperature sensor, replace if necessary.
Hope it helps.
Thank you for using FixYa.
(Positive feedback will be greatly appreciated.)
Oven does not work. I get an F-1 8 error message
Hi michael_d_fo,
The F1:-8 error code description is Keypad Shorted. Check to see if steam or other moisture is getting into clock assembly. Replace keypad if necessary.
Hope it helps.
Thank you for using FixYa.
(Positive feedback will be greatly appreciated.)
I got a F9-4 code
Hi szambarano,
The F9:-4 error code description is Latch Unlock Lower. Check for obstruction in door lock mechanism.
Hope it helps.
Thank you for using FixYa.
(Positive feedback will be greatly appreciated.)
Not finding what you are looking for?