20 Most Recent
Maytag MGR6772BDS Gemini Gas Kitchen Range - Page 3 Questions & Answers
MER6772 electric
digital display not working
Hi,
I am sorry to hear regarding the trouble.
Since the lights come on inside the oven, it means you're definitely
getting 120 volts. Unfortunately on this model there are no fuses or
cut out between the power supply and the display control board, so in case if the display board is is bad, you need to order and replace the control board itself.I have replaced quite a few in my shop. I am sorry to be a bearer of bad news, however replacement of control board is on the cards.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
8/11/2011 6:12:02 PM •
Maytag...
•
Answered
on Aug 11, 2011
My Maytag Gemini cooktop and top oven work. The
Replacing the ignitor is not difficult or dangerous. To get at it, you will first take out the racks. Then undo the box-like cover inside the bottom of the oven; the screws face front. Underneath that is a wing-shaped cover, held in place with wingnuts. Remove it.
The pipe that the gas comes out of heads straight back; the ignitor is just to the left. You'll be able to see the wires going out the back of the oven. Remove the plates that hold the tube/ignitor combination.
Once the pipe is free, then get your head out of the oven and pull out the oven so you can see, and get at, the back. On the lower left is a cover, about 12 x 15 or so, held in place by four screws. Remove it.
At this point you can see where the ignitor connects to the orange wires (at least mine are orange) with a plastic connection. Undo that connection.
Viola! You have removed the ignitor! Now, before you forget, make a diagram of everything you did. Put the screws in separate plastic baggies, with paper number tabs that correspond to your drawing. This will greatly help in putting everything back together.
2/16/2011 4:32:06 AM •
Maytag...
•
Answered
on Feb 16, 2011
I have a stove that
Sorry to read about your problem, I hope this helps you out.
you have a defective knob control switch.. must be replaced
I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck
12/24/2010 4:51:39 PM •
Maytag...
•
Answered
on Dec 24, 2010
My Maytag Gemini stove started igniting all the 4
You will need a new switch harness part#12002789 and spark module part#74007397.
1. You can gain access to the switch harness by unscrewing 2x screws on each of the burners
2. The remove old wire harness and replace with new
3. Follow the wire from the harness it will lead to the spark module now replace it
Good Luck
12/7/2010 4:58:14 PM •
Maytag...
•
Answered
on Dec 07, 2010
I have a Maytag Gas
the part number is 74004565 it cost about thirty dollars from a local parts supplier.it should just be able to be pulled out and pushed back inplace.
11/21/2010 5:12:03 PM •
Maytag...
•
Answered
on Nov 21, 2010
My Maytag Gemini Gas Range
If the broiler burner is not coming on it may be a bad ignitor or the ignitor may not be getting power. Observe the ignitor when you turn in on ans see if it glows at all. If not then test for power to the ignitor if you have power and not glowing or lighting replace the ignitor. If it glows but does not light the ignitor may just be weak replace it.
11/2/2010 11:51:02 PM •
Maytag...
•
Answered
on Nov 02, 2010
Maytag Range Gemini- neither oven is working.
try to reset the power / ? is the clock display working and are there any coded . // i would think that 1/2 of your power is out . this would cause the problem and yu may not heave any codes.. . so turn off the power and reset and see if it will work you will get a p f code ( power has failed so reset the clock and try it again ..mm feed back pls ..
10/30/2010 3:20:20 AM •
Maytag...
•
Answered
on Oct 30, 2010
Not finding what you are looking for?